BAYTEK GAMES SQUIGGLE

Questions and Answers

J
Jonathon RomeroAug 15, 2025
How to troubleshoot no power issue in BAYTEK GAMES SQUIGGLE?
- B
  Benjamin PowersAug 15, 2025
  If your BAYTEK GAMES Arcade Game Machine has no power, check the wall outlet cable to the line filter in the back of the game and the cable to the power strip. Ensure power cords are securely pushed into the power strip. Also, check the rocker switch on the power strip. Reset the power strip breaker switch or building circuit breaker. The cause may be that the appliance is unplugged, the power strip is turned off, the circuit breaker is tripped, the line filter is faulty, or the power supply is bad or overloaded. If needed, replace the line filter.
K
kristinapotterAug 18, 2025
What to do if the monitor is not working on my BAYTEK GAMES SQUIGGLE Arcade Game Machines?
- J
  Justin KhanAug 19, 2025
  If the BAYTEK GAMES Arcade Game Machine monitor displays 'No Signal' but the game plays, check the HDMI cable from the Raspberry Pi to the monitor. If the game doesn't play, the SD card might be faulty, so reseat or replace it. Also, check the small power connector on the Main Board and replace the power supply if needed. The HDMI cable might also be unplugged. If the monitor has nothing at all on power up, ensure the power cable is plugged into the monitor and that there is 110 VAC at the monitor. Also, ensure the TV is turned on. If these steps don't resolve the issue, the monitor might be faulty and need replacing.
A
Angela TaylorAug 21, 2025
Why my BAYTEK GAMES Arcade Game Machines game does not coin up?
- G
  gonzalezjohnAug 21, 2025
  If your BAYTEK GAMES Arcade Game Machines game does not coin up, set the “Game drive voltage threshold” to 2 volts. Check the coin signal wires (green and black wires) and their connections from the coin switches to the I/O Aux Board, checking for continuity. The issue may be due to pinched, broken, or disconnected wiring, or a faulty coin mechanism. Try swapping the coin mechanism to verify if it’s faulty. If there are communication issues, refer to the troubleshooting section for that. If the I/O Aux Board is faulty, replace it.
T
Thomas FrancoAug 30, 2025
How to troubleshoot wrong number of tickets dispensed on BAYTEK GAMES SQUIGGLE Arcade Game Machines?
- M
  michaelsmithAug 30, 2025
  If the wrong number of tickets is dispensed by your BAYTEK GAMES Arcade Game Machines, enter the “Payout Settings” menu and verify the correct settings for the Ticket Pattern. Ensure the number of tickets shown on the monitor is correct. Clean the opto-sensor with compressed air or wipe it with isopropyl alcohol on a cotton swab. Try flipping the tickets and loading them upside-down to have the large cut notch toward the opto sensor. Replace the ticket dispenser with a spare working dispenser. If possible, replace the main board to isolate the problem to a faulty I/O Aux Board. The issue might be due to the ticket pattern being set wrong, a sensor issue, a dirty opto-sensor, shallow notches on the tickets, a faulty ticket dispenser, or a main circuit board malfunction.
K
Kristi MeyersSep 2, 2025
Why are the red balls not coming down in my BAYTEK GAMES Arcade Game Machines?
- W
  William MccormickSep 2, 2025
  If the red balls are not coming down in your BAYTEK GAMES Arcade Game Machines, and the blower isn't running, check for constant 110 VAC on the input cable and a 12 Volt DC pulse. Also, check the fuse in the small box on the board and replace it if needed. If the green LED is on the board but there's no 110 VAC coming from the board, the AC Driver Board is faulty and needs replacing. If the blower is running, check for obstructions in the blower itself. If the blower is receiving 110 VAC but still not blowing, unplug the blower and check for obstructions. A ball may be jammed in the tube. The possible causes are that the AC Driver Board is not receiving power or a signal from the I/O Aux Board, the AC Driver Board isn't sending voltage to the blower, or the red ball path is blocked.
D
dschneiderSep 5, 2025
What causes BAYTEK GAMES Arcade Game Machines to dispense tickets all the time?
- J
  Jennifer GreeneSep 6, 2025
  If the BAYTEK GAMES Arcade Game Machines are dispensing tickets all the time, replace the Rasp Pi Board, as the ticket enable signal comes from the Rasp Pi Main Board.
J
John FrancisSep 8, 2025
What to do if bill acceptor is on but no signal on monitor in BAYTEK GAMES Arcade Game Machines?
- D
  Debbie WuSep 9, 2025
  To address a situation where the bill acceptor is on, but there's no signal on the monitor and everything else is off (Power Supply not ON) on your BAYTEK GAMES Arcade Game Machines, ensure the power supply is plugged into the power strip and that the rocker switch is set to ON. The issue may be caused by the power supply being unplugged, the rocker switch on the power supply being Off, the power supply shutting down because of a 12 V overload, or a faulty power supply. See the power supply diagnostics to isolate the bad component. A bad solenoid or 12 volt short could also cause this.
D
Dennis NortonSep 12, 2025
How to fix marquee LED lights that are not working on BAYTEK GAMES Arcade Game Machines?
- H
  Heather KaneSep 12, 2025
  If the Marquee LED lights are not working on your BAYTEK GAMES Arcade Game Machines, remove the marquee and examine the LED strip. Check the cables from the LED strip to the power distribution board. The causes may be a faulty LED strip or a faulty cable.
B
barkersusanNov 23, 2025
How to fix no audio or loud audio on BAYTEK GAMES Arcade Game Machines?
- S
  Shane WatkinsNov 23, 2025
  If you have no audio or the audio is too loud on your BAYTEK GAMES Arcade Game Machines, first, increase the volume by pressing the Menu button and going to “Volume & Attract Settings” to increase the Attract volume & Game Volume. You can also use the remote control to turn the volume down on the TV. Check the audio cable connections from the TV through the audio amplifier board to the speakers and the HMDI cable from the Motherboard. Ensure there is 12 VDC power on the cable from the power supply. A possible cause can be volume set too low, sound having static, loose wires, faulty HMDI cable from Motherboard or no 12 VDC power to Audio Amplifier board. To isolate the problem, unplug the phono jack from the audio filter from the TV and plug it into an MP3 player or phone to see if the soun...
K
Kelly DunnNov 26, 2025
What to do if tickets do not dispense from BAYTEK GAMES Arcade Game Machines?
- C
  Charles GrayNov 26, 2025
  If tickets do not dispense from your BAYTEK GAMES Arcade Game Machines, fill the ticket tray and ensure the low ticket switch is working. Check and repair any broken or loose wires. Clean the ticket tray of dirt, loose tickets, or debris. The switch wire may be bent out of position, so bend it to the correct position under the tickets. Check the wiring continuity from the dispenser to the I/O Aux Board, looking for pinched, broken, or disconnected wires. Clean the opto-sensor with compressed air or isopropyl alcohol. Try flipping the tickets to load them upside-down. If the notch signal isn't being seen, replace the I/O Aux Board. If the Enable signal is not present, replace the Raspberry Pi. Possible causes are an empty ticket tray, a faulty low ticket switch, broken/loose wires, a stuck ...