Name: Behringer FCB1010
Brand: Behringer
Rating: 5 (1 reviews)

To Next Page

To Previous Page

presets, please press footswitch 5 again. Press and hold DOWN/ESCAPE to quit the GLOBAL SETUP.

Toggling between two controller values in a patch

Allows you to configure one controller so that it alternately sends two different values, e.g. effect bypass, drive on/off, etc. In order to enable

the controller switch-over function, you need to globally select the same MIDI channel for CNT1 and CNT2 (see chapter 2.2), and enter the same

controller number for CNT1 and CNT2 in the preset (NUMBER, see chapter 2.3.2). The first time you recall the preset, it will send the controller

value of CNT1 (VALUE 1), with each additional key press you can alternate between CNT2 and CNT1. Example: Select preset 1 without DRIVE

function on the BEHRINGER V-AMP each time you press the same button again, DRIVE will be switched on or off respectively: PROG CHG 1 =

1, CNT 1 NUMBER = 26, VALUE 1 = 0, CNT 2 NUMBER = 26, VALUE 1 = 127.

1. Go into the utilities menu on the C-T & set the "cont.cont." from 11 to 14.

That will make the both pedals operational -globally. Then what I did so that I did not have to reassign stuff at every patch, was to make the "expression

Pedal" the master volume on all patches (This means that the inside pedal on the FCB1010 is always my master volume), and then I could use the outside

pedal on the FCB1010 as the; wah, gain, treble, echo brightness, etc, etc.

2. I downloaded Harriers PatchWizard. This makes it very easy to among other things manipulate patch locations within the Player Lounge. Eventually I

am going to try and use the top buttons on the FCB (6,7,8,9, & 10) for things like tuner on/ off & effects on/ off and nice stuff like that.

By only planning to use buttons 1-5 I still have 50 readily available patches -WAY MORE THEN I'LL EVER NEED TO GIG WITH. I positioned all my

patches at; P01-P05, P11-P15, P21-P25, P31-P36, etc.

Now I only have to worry about screwing around with one row of buttons.

I have found the C-T to be guitar sensitive, meaning different guitars really do cause the amp to sound or react differently (A good thing BTW)

Since I don't need 100 different sounds, I like to have a real saturated, Gainy, sustained, but not to dirty sound, basically the same character as the

previous just a bit cleaner, & a nice clean midrange well rounded tone. I am probably going to set the C-T up so that each bank of 5 is for a different guitar.

This will be another benefit to PatchWizard.

Plug in the foot pedal, turn it and the CT on. Hit the utilities button 4 times to get to the "Continuos Controller" and change that number to 14.

This gets the expression pedal B working. Then hit the button 4 more times (I think) to get to the "midi map" and assign any preset to a number

on the foot pedal by changing the preset number on the right to the one you want. You can then go into your presets on the CT and change the

Continuous Controller to any parameter you want to be affected by expression pedal B.

I have been able to figure out how to access the Cyber-Twin Tuner from the FCB1010 - here's how:

1. Any FCB Preset can be used as a "Tuner Access" Preset - you will sacrifice other things that this chosen FCB Preset can do, but you do have 100 to go

at, so pick a "sacrificial Preset" (I decided upon FCB Bank 9 Preset 9, so that I can just drop down a bank from my regular "most used" bank).

2. Go into programming mode for that FCB Preset, make sure that just "PROG CHG 1", and "CNT 1" are enabled...

3. Edit "CNT1" so that "NUMBER" (Controller Number) is 32, and "VALUE 1" is 1, 2, or 3 (Not ZERO!)

4. Edit "PROG CHG 1" so that "NUMBER" is 128

5. Exit FCB programming mode

You should now find that after selecting that FCB Bank (In my case I select Bank 9)... you can press the chosen Preset (9 in my case) and it will Activate

e 4 of 10Dear BEHRINGER users,

12/28/2002htt

://www.

atchwizard.com/

FCB1010.htm