Behringer ULTRA METAL UM300 User Manual

Thank you for showing your condence in us by purchasing the
Behringer ULTRA METAL UM300. This high-quality eects pedal comes
with a dual-gain circuitry that enables you to produce super thick, tube-
like distortion plus endless sustain. Thanks to its high-performance
features you will achieve the most extreme and sought-after hard rock
or heavy metal distortion sounds.
1. Controls
(1) The LOW control allows yu to boost/cut the lo-frequency range.
◊◊ Please keep in mind that extrme distortion and EQ
settings will increase nose and may induce oscillation.
(2) The two MID FREQ(uency) controls allow to boost/cut a dè ned
mid-frequency range. The upper control is used to increase
or lower the mid range, the cntrol below adjusts the center
frequency of the mid range that is aected (200 Hz to 5 kHz).
(3) The LEVEL control adjusts the output level.
(4) The ON/BATT LED illumnates when the eect is activated. It also
serves as a battery leve indicator.
(5) Use the footswitch to activate/deactivate the eect.
(6) Use this ¼" TS IN connector to plug in the instrument cable.
(7) The ¼" TS OUT connector sends the signal to your amp.
Use the DC IN connection to plug in a 9 V power supply (not included).
The BATTERY COMPARTMENT is located underneath the pedal cover.
To install or replace the 9 V battery, press the hinges with a ballpen and
remove the pedal cover. Be careful not to scratch the unit.
V1.0
ULTRA METAL UM300
Heavy Metal Distortion Eects Pedal
(3)
(1)
(5)
(4)
(7)
(2)
(8)
(6)
(9)

Behringer ULTRA METAL UM300 Specifications

Power

power supply voltage	9 V
power supply current	100 mA
power consumption	30 mA

Power Supply Compatibility

USA/Canada voltage	120 V~, 60 Hz
U.K./Australia voltage	240 V~, 50 Hz
China/Korea voltage	220 V~, 50 Hz
Europe voltage	230 V~, 50 Hz
Japan voltage	100 V~, 50 - 60 Hz

Connectivity

input connector	1/4" TS
input impedance	500 kΩ
output connector	1/4" TS
output impedance	1 kΩ

Weight and Dimensions

dimensions	54 mm x 70 mm x 123 mm
weight	0.33 kg

Summary

Controls Overview

LOW Frequency Control

Adjusts the low-frequency range, allowing boost or cut.

MID FREQ and Center Frequency Controls

Adjusts mid-frequency range and its center frequency (200 Hz to 5 kHz).

LEVEL Output Control

Adjusts the overall output volume level of the effect pedal.

ON/BATT LED Indicator

Indicates when the effect is activated and serves as a battery level indicator.

Footswitch Functionality

Used to activate or deactivate the effects pedal.

Input and Output Connections

Details the 1/4" TS IN for instrument and OUT for amplifier connection.

Power Supply and Battery Compartment

Explains DC IN connection and how to install/replace the 9V battery.

Safety and Warranty Information

General Safety Instructions

Advises against water, heat, unauthorized accessories, and self-servicing.

Limited Warranty Details

Provides information on warranty terms and conditions, with a link for more details.

Technical Specifications

Input and Output Specifications

Details connector type (1/4" TS) and impedance for both input and output.

Power Supply Requirements

Lists voltage, current, connector type, battery type, and power consumption.

Physical Dimensions and Weight

Provides the physical size (H x W x D) and weight of the pedal.

Federal Communications Commission Compliance

FCC Part 15 Compliance Statement

Details compliance with FCC rules for Class B digital devices and potential interference.

Important Information on Modifications

Warns that unauthorized modifications can void the user's authority to operate the equipment.

CE Declaration of Conformity

EU Product Compliance Directives

Lists the directives and regulations the product conforms to, including REACH.

EU Representative Contact Information

Provides the address and name of the EU representative for Music Tribe.