What to do if the Beko WTG1041B2W Washer programme cannot be started or selected?
If a programme cannot be started or selected on your Beko Washer, it may have switched to self-protection mode due to a supply problem (line voltage, water pressure, etc.). To cancel the programme, turn the Programme Selection knob to select another programme. The previous programme will be cancelled.
Why do my clothes smell unpleasant after washing in my Beko Washer?
If your clothes smell unpleasant after being washed in your Beko Washer, it's likely due to odours and bacteria forming on the drum from continuous washing at low temperatures and/or in short programmes. To prevent this, leave the detergent drawer and the loading door ajar after each wash to discourage bacteria growth.
Why doesn't my laundry smell like softener after using my Beko WTG1041B2W?
If your laundry doesn't smell like softener after washing in your Beko Washer: * Detergent is put in the wrong compartment. If detergent is put in the prewash compartment although prewash cycle is not selected, machine can take this detergent during rinsing or softener step. Wash and clean the dispenser with hot water. Put the detergent in the correct compartment. * Detergent might be mixed with the softener. Do not mix the softener with detergent. Wash and clean the dispenser with hot water.
Why is foam overflowing from the detergent drawer of my Beko WTG1041B2W Washer?
If foam is overflowing from the detergent drawer of your Beko Washer: * Too much detergent is used. Mix 1 tablespoonful softener and ½ l water and pour into the main wash compartment of the detergent drawer. * Put detergent into the machine suitable for the programmes and maximum loads indicated in the “Programme and consumption table”. When you use additional chemicals (stain removers, bleachs and etc), reduce the amount of detergent.
Why is my laundry stiff after washing in my Beko WTG1041B2W Washer?
If your laundry becomes stiff after washing in your Beko Washer, it could be because: * You're using too little detergent. Use appropriate amount of detergent according to the water hardness. * The detergent is in the wrong compartment. If detergent is put in the prewash compartment although prewash cycle is not selected, machine can take this detergent during rinsing or softener step. Put the detergent in the correct compartment. * The detergent is mixed with softener. Do not mix the softener with detergent. Wash and clean the dispenser with hot water.
Why is there too much foam in my Beko WTG1041B2W?
If your Beko Washer is producing too much foam, it could be due to: * Using improper detergents. Use detergents appropriate for washing machines. * Using too much detergent. Use only a sufficient amount. * Improper detergent storage. Store detergent in a closed and dry location. Do not store in excessively hot places. * The type of laundry. Use smaller amounts of detergent for meshed laundry. * Putting detergent in the wrong compartment. Put the detergent in the correct compartment. * Softener being taken early. There may be problem in the valves or in the detergent dispenser. Call the Authorised Service Agent.
Why is my Beko WTG1041B2W taking longer than the specified time?
Several factors can cause your Beko Washer to take longer than usual: * Low water pressure: The machine waits for adequate water intake. * Low voltage: The washing time is prolonged to compensate. * Low input water temperature: Heating takes longer. * Increased number of rinses or rinse water amount: The machine adjusts for better rinsing. * Excessive foam: The automatic foam absorption system activates.
Why is my Beko Washer vibrating or making noise?
There are several reasons why your Beko Washer might be vibrating or making noise: * The machine might be unbalanced. Try adjusting the feet to level it. * A hard substance might be in the pump filter. Clean the pump filter. * The transportation safety bolts might not be removed. Remove them. * The laundry quantity might be too little. Add more laundry. * The machine might be overloaded. Take some laundry out or redistribute it. * The machine might be leaning on something. Ensure it's not.
Why did my Beko Washer stop shortly after the programme started?
If your Beko Washer stopped shortly after the program started, it might have stopped temporarily due to low voltage. It will resume running when the voltage restores to the normal level.
What to do if my Beko WTG1041B2W Washer does not drain water?
If your Beko Washer isn't draining water, the water drain hose might be clogged or twisted, so try cleaning or flattening the hose. Alternatively, the pump filter might be clogged, so try cleaning the pump filter.
General| Type | Front Load |
|---|---|
| Washing Capacity | 10 kg |
| Spin Speed | 1400 rpm |
| Energy Efficiency Class | A+++ |
| Number of Programs | 15 |
| Color | White |
| Noise Level Washing | 53 dB |
To Next Page
