Why does my Beko WTK84011W directly discharge the water it takes in?
If your Beko Washer immediately discharges the water it takes in, the draining hose might not be at the correct height. Connect the water draining hose as described in the operation manual.
What to do if my Beko WTK84011W loading door won't open?
If you can't open the loading door of your Beko Washer: * The door lock might be activated due to the water level, so drain the water by running the Pump or Spin programme. * The machine might be heating or spinning, so wait until the programme completes. * The child lock might be engaged, so wait a couple of minutes after the programme ends for it to deactivate. * The door might be stuck due to pressure, so try pushing and pulling the door to release it.
What to do if my Beko WTK84011W programme does not start?
If the programme on your Beko Washer doesn't start after closing the door: * Make sure you've pressed the Start / Pause / Cancel button. * If the loading door is hard to close, you may have loaded too much laundry, so reduce the amount and ensure the door is closed properly.
Why is my Beko WTK84011W Washer not switching to spinning?
Your Beko Washer might not switch to the spinning step because: * There might be an unbalanced load, so the automatic unbalanced load detection system might be activated. * The machine won't spin if water isn't drained completely, so check the filter and draining hose. * Excessive foam might have occurred, activating the automatic foam absorption system due to too much detergent, so use the recommended amount of detergent.
Why does my Beko WTK84011W Washer enter standby mode or not take in water?
If your Beko Washer enters standby mode or doesn't take in water: * Check if the tap is turned off and turn it on. * Ensure the water inlet hose isn't bent and flatten it if it is. * Clean the water inlet filter if it's clogged. * Make sure the loading door is closed. * Verify the water connection and ensure water isn't cut off. If it was cut off, press the Start/Pause key after the water supply resumes.
Why is there water leaking from the bottom of my Beko Washing machine?
If water is leaking from the bottom of your Beko washing machine, the water drain hose might be clogged or twisted, so clean or flatten the hose. Additionally, the pump filter might be clogged, so clean the pump filter.
Why does too much foam form in my Beko Washing machine?
Excessive foam in your Beko washing machine can be caused by: * Using improper detergents, so use detergents appropriate for washing machines. * Using too much detergent, so use only a sufficient amount. * Improper detergent storage, so store detergent in a closed, dry location, not in excessively hot places. * Washing meshed laundry like tulle, which may foam too much, so use smaller amounts of detergent for these items. * Putting detergent in the wrong compartment, so use the correct compartment. * Softener being taken early, which may indicate a problem in the valves or detergent dispenser.
Why does my Beko WTK84011W Washer have poor washing performance and laundry turns gray?
Poor washing performance with gray laundry in your Beko Washer can be due to: * Using too little detergent over time, so use the recommended amount for water hardness and laundry. * Washing at low temperatures for too long, so select the proper temperature. * Using too little detergent with hard water, so use the recommended amount. * Using too much detergent, so use the recommended amount.
What to do if my Beko WTK84011W Washer programme cannot be started?
If a programme cannot be started or selected on your Beko Washer, the machine may have switched to self-protection mode due to a supply problem (line voltage, water pressure, etc.). To cancel the programme, turn the Programme Selection knob to select another programme. The previous programme will be cancelled.
Why is there detergent residue in my Beko Washer drawer?
Detergent residue in the drawer of your Beko Washer can occur for several reasons: * The detergent was put in a wet drawer, so dry the drawer before adding detergent. * The detergent has gotten damp, so keep detergents closed in a humidity-free environment and avoid excessive temperatures. * The water pressure is low, so check the water pressure. * The holes of the detergent compartment are blocked, so check and clean them if clogged. * Detergent might be mixed with the softener, so do not mix the softener with detergent and wash and clean the dispenser with hot water.
Safety guidelines for preventing harm to people and property, including child safety.
Precautions regarding electrical connections and hot surfaces during operation.
Selecting a location, removing packaging, and dealing with transport locks.
Connecting the water supply, drain hose, and electrical power safely.
Guidance on using detergents, softeners, and other washing agents.
Tips for energy saving and optimal washing based on fabric and soiling.
Solutions for programs not starting, water intake, and drainage failures.
Safety guidelines for preventing harm to people and property, including child safety.
Precautions regarding electrical connections and hot surfaces during operation.
Selecting a location, removing packaging, and dealing with transport locks.
Connecting the water supply, drain hose, and electrical power safely.
Guidance on using detergents, softeners, and other washing agents.
Tips for energy saving and optimal washing based on fabric and soiling.
Solutions for programs not starting, water intake, and drainage failures.
General| Door hinge | Left |
|---|---|
| Motor type | Brushless |
| Water fill | Cold |
| Control type | Rotary |
| Loading type | Front-load |
| Drum material | Stainless steel |
| Product color | White |
| Built-in display | Yes |
| Custom panel-ready | No |
| Door opening angle | 170 ° |
| Outlet hose length | 1.3 m |
| Appliance placement | Freestanding |
| Feet adjustment | 15 mm |
| Drum capacity | 8 kg |
| Cycle time (max) | 218 min |
| AquaStop function | - |
| Delay start (max) | 9 h |
| Residual moisture | 53 % |
| Spin-drying class | B |
| Maximum spin speed | 1400 RPM |
| Noise level (spin) | 72 dB |
| Noise level (wash) | - dB |
| Number of washing programs | 15 |
| Maximum washing temperature | 90 °C |
| Maximum water flow pressure | 1000 kPa |
| Minimum water flow pressure | 100 kPa |
| Cycle time (quick washing program) | 28 min |
| Current | 10 A |
| Connected load | 2200 W |
| Power plug type | Type G |
| AC input voltage | 230 V |
| AC input frequency | 50 Hz |
| Energy efficiency scale | A to G |
| Power consumption (off) | 0.5 W |
| Power consumption (standby) | 1 W |
| Water consumption per cycle | 41 L |
| Energy consumption washing per cycle | 0.623 kWh |
| Energy efficiency index (EU 2017/1369) | 1.04 |
| Package width | 650 mm |
| Package height | 880 mm |
| Package weight | 69000 g |
| Hose diameter | 20 mm |
| Required tools | Standard tool box |
| Paper packaging weight | 10 g |
| Plastic packaging weight | 178 g |
| Harmonized System (HS) code | 84501190 |
| Expanded Polystyrene (EPS) packaging weight | 788 g |
Weight and Dimensions| Depth | 590 mm |
|---|---|
| Width | 600 mm |
| Height | 840 mm |
| Weight | 68000 g |
| Door opening diameter | 340 mm |
To Next Page
