EasyManua.ls Logo

Beko WTK62051W - User Manual

Beko WTK62051W
44 pages
Print Icon
To Next Page IconTo Next Page
To Next Page IconTo Next Page
Loading...
Washing Machine
User Manual
WTK62051W
2820528268_EN/ 02-03-20.(16:05)
Document Number :

Questions and Answers

  • Q
    qalvarezSep 23, 2025
    Why no water can be seen in the Beko WTK62051W Washer during washing?
    • V
      Vicki SmithSep 23, 2025
      This is not a failure.
  • C
    Christopher Bowen DDSAug 23, 2025
    Why is there water leaking from the bottom of my Beko washing machine?
    • J
      jonathoncaseyAug 23, 2025
      If you see water leaking from the bottom of your Beko washing machine, the water drain hose might be clogged or twisted. Clean or flatten the hose. Also, the pump filter might be clogged, so clean the pump filter.
  • T
    Tanya GrahamAug 25, 2025
    Why does my Beko WTK62051W not rinse well?
    • S
      Sherry RobertsAug 26, 2025
      If your Beko Washer isn't rinsing well, the amount, brand, or storage conditions of the detergent might be inappropriate. Use a detergent suitable for washing machines and your laundry, and store detergents properly. Ensure detergent is placed in the correct compartment. Also, check the pump filter and drain hose for clogs or folds.
  • M
    Michael DurhamAug 26, 2025
    What to do if the loading door of my Beko WTK62051W Washer won't open?
    • M
      Mary PerezAug 27, 2025
      If your Beko Washer's loading door won't open, it could be due to several reasons. The door lock might be activated because of the water level; try running the Pump or Spin programme to drain the water. If the machine is heating water or is in the spinning cycle, wait until the programme completes. If the child lock is engaged, wait a couple of minutes after the programme ends for it to deactivate. Lastly, the door might be stuck due to pressure; try pushing and pulling the door to release it.
  • M
    Mary BrownAug 27, 2025
    How to start a Beko WTK62051W after closing the door?
    • N
      Nathan BriggsAug 27, 2025
      If your Beko Washer isn't starting after you close the door, make sure you've pressed the Start / Pause / Cancel button. Also, check if you've overloaded the machine, as this can make it difficult to close the loading door properly. Reduce the amount of laundry and ensure the door is fully closed.
  • D
    David WalkerSep 16, 2025
    Why does too much foam form in my Beko Washer?
    • N
      Natalie SanchezSep 16, 2025
      If too much foam forms in your Beko Washer, ensure you're using detergents appropriate for washing machines and only use a sufficient amount. Store detergent in a closed, dry location away from heat. For meshed laundry like tulle, use less detergent. Ensure detergent is placed in the correct compartment. If softener is being taken early, there may be a problem in the valves or in the detergent dispenser. Call the Authorised Service Agent.
  • D
    Derrick HatfieldSep 13, 2025
    Why does the laundry not smell like the softener after using my Beko Washer?
    • J
      jeffrey83Sep 13, 2025
      If laundry doesn't smell like softener after washing in your Beko Washer, ensure detergent isn't put in the wrong compartment. If detergent is put in the prewash compartment although prewash cycle is not selected, machine can take this detergent during rinsing or softener step. Wash and clean the dispenser with hot water. Also, avoid mixing softener with detergent.
  • C
    Casey TurnerSep 14, 2025
    Why is there detergent residue in the detergent drawer of my Beko WTK62051W?
    • R
      Richard ColemanSep 15, 2025
      If there's detergent residue in the drawer of your Beko Washer, dry the drawer before adding detergent. Ensure the detergent hasn't gotten damp and that water pressure is adequate. Check for and clear any blockages in the detergent compartment holes. If there is a problem with the detergent drawer valves, call the Authorised Service Agent. Avoid mixing softener with detergent and clean the drum regularly.
  • H
    Hector ScottSep 5, 2025
    Why is the Beko WTK62051W taking longer than specified in the manual?
    • A
      Amanda ReedSep 5, 2025
      If your Beko Washer is taking longer than expected, several factors could be contributing. Low water pressure can cause the machine to wait until it takes in enough water, extending the wash time. Similarly, low voltage or low input water temperature can prolong the process. The machine may also increase the amount of rinse water or add an extra rinse step if needed. Excessive foam from using too much detergent can also activate the automatic foam absorption system, increasing wash time. Use recommended amount of detergent.
  • D
    Desiree BoothSep 3, 2025
    Why does my Beko WTK62051W Washer leave laundry wet at the end of the programme?
    • C
      chaseaaronSep 3, 2025
      If your Beko Washer leaves laundry wet at the end of the programme, it could be due to excessive foam activating the automatic foam absorption system. Use the recommended amount of detergent.

Summary

General Safety Instructions

Life and Property Safety

Safety precautions to prevent injuries and material damage.

Childrens Safety

Guidelines for safe use of the appliance by children.

Electrical Safety

Precautions regarding electrical connections and potential shocks.

Your Product

Installation Guide

Step-by-step instructions for installing the washing machine.

Detergent and Softener Usage

How to use detergents, softeners, and other cleaning agents.

Operating the Product

Programme and Consumption Data

Table detailing wash programmes, duration, and consumption.

Maintenance and Cleaning

Draining Water and Pump Filter

Procedure for draining residual water and cleaning the pump filter.

Troubleshooting Common Issues

Programme Operation Problems

Solutions for issues with starting, selecting, or running programmes.

Water Intake and Drainage Issues

Troubleshooting for water intake, draining, and leakage problems.

Standard Manufacturer Guarantee Terms

Obtaining Service and Support

Beko WTK62051W Specifications

General IconGeneral
Door hingeLeft
Water fillCold
Control typeButtons, Rotary
Loading typeFront-load
Product colorWhite
Built-in displayYes
Door opening angle170 °
Outlet hose length1.3 m
Appliance placementFreestanding
Feet adjustment15 mm
Remaining time indicationNo
Drum capacity6 kg
Cycle time (max)197 min
AquaStop function-
Delay start (max)9 h
Residual moisture53 %
Spin-drying classB
Maximum spin speed1200 RPM
Noise level (spin)76 dB
Noise level (wash)- dB
Number of washing programs15
Maximum water flow pressure1000 kPa
Minimum water flow pressure100 kPa
Cycle time (quick washing program)28 min
Current13 A
Connected load1550 W
Power plug typeType G
AC input voltage230 V
AC input frequency50 Hz
Energy efficiency scaleA to G
Power consumption (off)0.5 W
Power consumption (standby)1 W
Water consumption per cycle43 L
Energy consumption washing per cycle0.733 kWh
Package depth465 mm
Package width650 mm
Package height880 mm
Package weight57000 g
Washing classA
Paper packaging weight10 g
Plastic packaging weight178 g
Harmonized System (HS) code84501190
Expanded Polystyrene (EPS) packaging weight733 g
Weight and Dimensions IconWeight and Dimensions
Depth440 mm
Width600 mm
Height840 mm
Weight56000 g
Door opening diameter300 mm

Related product manuals