Why programme time does not countdown on my Beko Washer? (On models with display)
If the programme time isn't counting down on your Beko Washer (for models with a display), the timer may pause during water intake until enough water is in the machine, or during heating until the selected temperature is reached. It might also stop during spinning if the load is unbalanced.
Why is my Beko WTK72011W not draining water?
If your Beko Washer isn't draining water, check if the water drain hose is clogged or twisted, and clean or straighten it. Also, inspect the pump filter for clogs and clean it.
Why my Beko WTK72011W doesn't rinse well?
If your Beko Washer isn't rinsing well, make sure you're using the right detergent for your machine and laundry, and that it's stored properly. Ensure you're putting the detergent in the correct compartment. Also, check the pump filter and drain hose for any clogs or folds.
What to do if there is water leaking from the bottom of my Beko WTK72011W Washer?
If your Beko Washer is leaking water, examine the water drain hose for any clogs or twists, and clean or straighten it. Additionally, check the pump filter for blockages and clean it if necessary.
Why can't I start or select a programme on my Beko WTK72011W Washer?
If your Beko Washer programme cannot be started or selected, it might be in self-protection mode because of a supply issue like voltage or water pressure. To cancel the current programme, turn the Programme Selection knob to another programme. This will cancel the previous selection.
Why is washing performance poor and stains persist or the laundry is not whitened after washing in my Beko Washer?
If your Beko Washer washing performance is poor and stains persist or the laundry is not whitened, ensure you are using enough detergent for the load size and water hardness. Avoid overloading the machine and select the correct programme and temperature for the items being washed. Use the right type of detergent and put it in the correct compartment, without mixing it with bleaching agents.
Why is foam overflowing from the detergent drawer of my Beko Washer?
If foam is overflowing from the detergent drawer of your Beko Washer, it's likely due to using too much detergent or mixing detergent with softener. Mix one tablespoon of softener with half a liter of water and pour it into the main wash compartment. Use detergent suitable for the programmes and loads indicated in the manual, and reduce the amount if you're using additional chemicals like stain removers.
Why is my washing performance poor and oily stains appeared on the laundry after washing in Beko WTK72011W Washer?
If your Beko Washer washing performance is poor and oily stains appeared on the laundry, you should clean the drum regularly.
Why is the washing performance poor and laundry turns gray in my Beko WTK72011W?
If your Beko Washer laundry turns gray, it could be from using too little detergent over time, washing at low temperatures, or using too little detergent with hard water. Use the recommended amount of detergent for your water hardness and laundry type. Note that it's difficult to reverse graying once it occurs. Also, avoid using too much detergent.
Why does my Beko WTK72011W stop shortly after the programme started?
If your Beko Washer keeps stopping shortly after starting, it might be due to low voltage. The machine should resume when the voltage returns to normal.
Safety guidelines to prevent injury and damage to property.
Precautions for child safety around the washing machine.
Essential electrical safety measures for operating the appliance.
Steps to remove transit packaging and safety bolts before operation.
Instructions for correctly connecting the water inlet and drain hoses.
Guidance on safely connecting the washing machine to the electrical supply.
Guidance on correct load size and appropriate use of detergent and softener.
Identifies and describes the functions of the control panel elements.
Guidance on selecting wash programmes and preparing the machine.
A detailed table of wash programmes, settings, and consumption data.
General| Door hinge | Left |
|---|---|
| Motor type | Brushless |
| Water fill | Cold |
| Control type | Rotary |
| Loading type | Front-load |
| Drum material | Stainless steel |
| Product color | White |
| Built-in display | Yes |
| Custom panel-ready | No |
| Door opening angle | 170 ° |
| Outlet hose length | 1.3 m |
| Appliance placement | Freestanding |
| Feet adjustment | 15 mm |
| Drum capacity | 7 kg |
| Cycle time (max) | 207 min |
| AquaStop function | - |
| Delay start (max) | 9 h |
| Residual moisture | 52 % |
| Spin-drying class | B |
| Maximum spin speed | 1200 RPM |
| Noise level (spin) | 74 dB |
| Noise level (wash) | - dB |
| Number of washing programs | 15 |
| Maximum water flow pressure | 1000 kPa |
| Minimum water flow pressure | 100 kPa |
| Cycle time (quick washing program) | 28 min |
| Current | 10 A |
| Connected load | 2200 W |
| Power plug type | Type G |
| AC input voltage | 230 V |
| AC input frequency | 50 Hz |
| Energy efficiency scale | A to G |
| Power consumption (off) | 0.5 W |
| Power consumption (standby) | 1 W |
| Water consumption per cycle | 45 L |
| Energy consumption washing per cycle | 0.685 kWh |
| Energy efficiency index (EU 2017/1369) | 1.04 |
| Package depth | 560 mm |
| Package width | 650 mm |
| Package height | 880 mm |
| Package weight | 64000 g |
| Hose diameter | 20 mm |
| Washing class | A |
| Required tools | Standard tool box |
| Paper packaging weight | 10 g |
| Plastic packaging weight | 178 g |
| Harmonized System (HS) code | 84501190 |
| Expanded Polystyrene (EPS) packaging weight | 760 g |
Weight and Dimensions| Depth | 550 mm |
|---|---|
| Width | 600 mm |
| Height | 840 mm |
| Weight | 63000 g |
| Door opening diameter | 300 mm |
To Next Page
