Why is the colour of the clothes faded after washing in my Beko Washer?
If your Beko Washer clothes faded, avoid overloading the machine. Ensure your detergent is not damp and stored properly, away from humidity and extreme temperatures. Select the correct programme and temperature for your laundry type and how dirty it is.
What to do if the loading door of my Beko WTK72011W cannot be opened?
If your Beko Washer door won't open, and there's water inside, try running the Pump or Spin programme to drain it. If the machine is heating or spinning, wait for it to finish. If the child lock is on, wait a few minutes after the programme ends for it to deactivate. If the door seems stuck, try pushing and pulling it to release any pressure.
Why does my Beko WTK72011W Washer directly discharge the water it takes in?
If your Beko Washer is directly discharging water, ensure the draining hose is connected at the correct height, as described in the operation manual.
Why does my Beko WTK72011W stop shortly after the programme started?
If your Beko Washer keeps stopping shortly after starting, it might be due to low voltage. The machine should resume when the voltage returns to normal.
Why does washing take longer time than specified in the manual on my Beko Washer?
If your Beko Washer washing cycle is taking longer than usual, it could be due to low water pressure. The machine waits until it has enough water, which extends the wash time. Low voltage or a low input water temperature can also prolong the cycle. The machine may also increase rinse water or add an extra rinse if needed, or excessive foam might have occurred due to too much detergent. Make sure to use the recommended amount of detergent.
How to start a Beko WTK72011W Washer programme after closing the door?
If your Beko Washer programme doesn't start after closing the door, make sure you've pressed the Start / Pause / Cancel button. Also, check that you haven't overloaded the machine, as this can make it difficult to close the door properly. Reduce the amount of laundry if necessary and ensure the door is securely closed.
Why is my Beko WTK72011W vibrating or making noise?
If your Beko Washer vibrates or makes noise, make sure it's level by adjusting the feet. Check the pump filter for any hard objects and clean it if needed. Ensure the transportation safety bolts have been removed. Adjust the laundry load; adding more if it's too little, or removing some if it's overloaded. Also, check that the machine isn't leaning against anything.
Why does my laundry remain wet at the end of the Beko WTK72011W programme?
If your Beko Washer laundry remains wet, it may be due to excessive foam from using too much detergent. Try using the recommended amount of detergent.
Why can't I start or select a programme on my Beko WTK72011W Washer?
If your Beko Washer programme cannot be started or selected, it might be in self-protection mode because of a supply issue like voltage or water pressure. To cancel the current programme, turn the Programme Selection knob to another programme. This will cancel the previous selection.
What to do if there is water leaking from the bottom of my Beko WTK72011W Washer?
If your Beko Washer is leaking water, examine the water drain hose for any clogs or twists, and clean or straighten it. Additionally, check the pump filter for blockages and clean it if necessary.
Safety guidelines to prevent injury and damage to property.
Precautions for child safety around the washing machine.
Essential electrical safety measures for operating the appliance.
Steps to remove transit packaging and safety bolts before operation.
Instructions for correctly connecting the water inlet and drain hoses.
Guidance on safely connecting the washing machine to the electrical supply.
Guidance on correct load size and appropriate use of detergent and softener.
Identifies and describes the functions of the control panel elements.
Guidance on selecting wash programmes and preparing the machine.
A detailed table of wash programmes, settings, and consumption data.
General| Door hinge | Left |
|---|---|
| Motor type | Brushless |
| Water fill | Cold |
| Control type | Rotary |
| Loading type | Front-load |
| Drum material | Stainless steel |
| Product color | White |
| Built-in display | Yes |
| Custom panel-ready | No |
| Door opening angle | 170 ° |
| Outlet hose length | 1.3 m |
| Appliance placement | Freestanding |
| Feet adjustment | 15 mm |
| Drum capacity | 7 kg |
| Cycle time (max) | 207 min |
| AquaStop function | - |
| Delay start (max) | 9 h |
| Residual moisture | 52 % |
| Spin-drying class | B |
| Maximum spin speed | 1200 RPM |
| Noise level (spin) | 74 dB |
| Noise level (wash) | - dB |
| Number of washing programs | 15 |
| Maximum water flow pressure | 1000 kPa |
| Minimum water flow pressure | 100 kPa |
| Cycle time (quick washing program) | 28 min |
| Current | 10 A |
| Connected load | 2200 W |
| Power plug type | Type G |
| AC input voltage | 230 V |
| AC input frequency | 50 Hz |
| Energy efficiency scale | A to G |
| Power consumption (off) | 0.5 W |
| Power consumption (standby) | 1 W |
| Water consumption per cycle | 45 L |
| Energy consumption washing per cycle | 0.685 kWh |
| Energy efficiency index (EU 2017/1369) | 1.04 |
| Package depth | 560 mm |
| Package width | 650 mm |
| Package height | 880 mm |
| Package weight | 64000 g |
| Hose diameter | 20 mm |
| Washing class | A |
| Required tools | Standard tool box |
| Paper packaging weight | 10 g |
| Plastic packaging weight | 178 g |
| Harmonized System (HS) code | 84501190 |
| Expanded Polystyrene (EPS) packaging weight | 760 g |
Weight and Dimensions| Depth | 550 mm |
|---|---|
| Width | 600 mm |
| Height | 840 mm |
| Weight | 63000 g |
| Door opening diameter | 300 mm |
To Next Page
