How to fix a Beko WTK62041W Washer that does not drain water?
If your Beko Washer isn't draining water, the water drain hose might be clogged or twisted; clean or flatten it. Alternatively, the pump filter might be clogged; clean the pump filter.
Why is my Beko Washer leaking water from the bottom?
If water is leaking from the bottom of your Beko Washer, the water drain hose might be clogged or twisted; clean or flatten it. Also, the pump filter might be clogged, so clean the pump filter.
Why can't I start or select a programme on my Beko WTK62041W Washer?
If a programme cannot be started or selected on your Beko Washer, the machine may have switched to self-protection mode due to a supply problem (line voltage, water pressure, etc.). To cancel the programme, turn the Programme Selection knob to select another programme. The previous programme will be cancelled.
What to do if Beko WTK62041W enters standby mode or doesn't take in water?
If your Beko Washer enters standby mode or doesn't take in water, check the following: ensure the tap is turned on, the water inlet hose isn't bent (flatten it if it is), and the water inlet filter isn't clogged (clean it if it is). Also, make sure the loading door is closed properly. Finally, verify the water connection and ensure water isn't cut off; if it was, press the Start/Pause button after water is restored.
Why doesn't my Beko WTK62041W rinse well?
If your Beko Washer isn't rinsing well, the amount, brand, or storage conditions of the detergent might be inappropriate; use a detergent appropriate for the machine and your laundry, and store detergents closed in a humidity-free environment, away from excessive temperatures. Detergent might be in the wrong compartment; if detergent is in the prewash compartment without selecting a prewash cycle, the machine might take it during rinsing. Also, the pump filter could be clogged (check the filter), or the drain hose could be folded (check the drain hose).
What to do if Beko WTK62041W programme doesn't start after closing the door?
If the Beko Washer programme doesn't start after closing the door, ensure you've pressed the Start / Pause / Cancel button. Also, if you've loaded too much laundry, it may be difficult to close the door properly; reduce the amount of laundry and make sure the door is fully closed.
Why is my laundry still wet after Beko WTK62041W programme ends?
If laundry remains wet after a Beko Washer programme, excessive foam might have occurred, activating the automatic foam absorption system due to too much detergent usage. Use the recommended amount of detergent.
Why does my Beko Washer immediately discharge the water it takes in?
If your Beko Washer immediately discharges the water it takes in, the draining hose might not be at an adequate height. Connect the water draining hose as described in the operation manual.
Why is my Beko Washer vibrating and making noise?
There are several reasons why your Beko Washer might be vibrating or making noise. It could be standing unbalanced, so adjust the feet to level it. A hard substance might have entered the pump filter, so try cleaning the pump filter. Ensure the transportation safety bolts are removed. The laundry quantity might be too little or too much; add more laundry or take some out to balance the load. Also, make sure the machine isn't leaning on anything.
Why does my Beko WTK62041W take longer than the manual says?
Several factors can cause your Beko Washer to take longer than expected. Low water pressure causes the machine to wait until it has enough water, extending the wash time. Low voltage can also prolong the washing time to ensure good results. A low input water temperature will extend the time needed to heat the water. The machine may also increase the amount of rinse water or add an extra rinse if needed. Finally, excessive foam from too much detergent can activate the automatic foam absorption system, increasing wash time; use the recommended amount of detergent.
General| Type | Freestanding |
|---|---|
| Capacity | 6 kg |
| Energy Efficiency Class | A+++ |
| Spin Speed | 1200 rpm |
| Number of Programs | 15 |
| Color | White |
| Noise level spinning | 76 dB |
To Next Page
