What to do if my Beko WTG921B2W Washer won't drain?
If your Beko Washer isn't draining water, the water drain hose might be clogged or twisted, so you should clean or flatten it. Alternatively, the pump filter could be clogged and needs cleaning.
Why is my Beko Washer leaking from the bottom?
If you see water leaking from the bottom of your Beko Washer, the water drain hose might be clogged or twisted, so clean or flatten it. Also, the pump filter might be clogged, requiring cleaning.
Why is my Beko Washer not rinsing properly?
If your Beko Washer isn't rinsing well, consider these possibilities: The detergent might be inappropriate, or its storage conditions might be poor; ensure you use the correct detergent, stored properly. The detergent could be in the wrong compartment; put it in the correct one. The pump filter might be clogged, so check the filter. The drain hose could be folded, so inspect the drain hose.
Why can't I start my Beko WTG921B2W Washer programme?
If your Beko Washer programme cannot be started or selected, the washing machine may have switched to self-protection mode because of a supply problem (line voltage, water pressure, etc.). To cancel the programme, turn the Programme Selection knob to select another programme. The previous programme will be cancelled.
How to start Beko WTG921B2W after closing the door?
If your Beko Washer doesn't start after closing the door, make sure you press the Start / Pause / Cancel button. Also, if you've loaded too much laundry, it may be difficult to close the loading door properly. Reduce the amount of laundry and ensure the door is closed correctly.
Why is my Beko WTG921B2W Washer vibrating so much?
If your Beko Washer vibrates or makes noise, several factors could be responsible. The machine might be unbalanced, so adjust the feet to level it. A hard substance may have entered the pump filter, requiring you to clean it. Ensure the transportation safety bolts have been removed. The laundry quantity might be too little or too much; adjust the load accordingly. Finally, ensure the machine isn't leaning on anything.
Why does my Beko WTG921B2W Washer take so long to wash?
If your Beko Washer takes longer than expected, it could be due to several reasons. Low water pressure causes the machine to wait until it has enough water, extending the wash time. Low voltage can also prolong the wash cycle to ensure good results. Cold water input requires more time to heat the water. The machine may also increase the rinse water or add an extra rinse if needed. Finally, excessive foam from too much detergent can activate the foam absorption system, lengthening the cycle. Use the recommended amount of detergent to avoid this.
Why is there detergent residue in my Beko Washer drawer?
If there's detergent residue in the drawer of your Beko Washer, it might be because the detergent drawer was wet when you added detergent; dry the drawer before adding detergent. The detergent may have gotten damp; store detergents properly in a dry, closed environment. Low water pressure could be a factor; check the water pressure. The holes of the detergent compartment might be blocked; check and clean them if necessary. There may be a problem with the detergent drawer valves, in which case you should call the Authorised Service Agent. Also, make sure you are not mixing the softener with detergent; wash and clean the dispenser with hot water.
Why is my Beko WTG921B2W Washer making too much foam?
If your Beko Washer is producing too much foam, make sure you're using detergents suitable for washing machines. You might be using too much detergent; use only a sufficient amount. Improperly stored detergent could be the issue; store it in a closed, dry location, away from excessive heat. Some meshed laundry items may create excessive foam; use less detergent for these items. Ensure you're putting the detergent in the correct compartment. If softener is being taken early, there may be a problem in the valves or in the detergent dispenser, in which case you should call the Authorised Service Agent.
Why did my Beko WTG921B2W stop soon after starting?
If your Beko Washer stopped shortly after starting, it might have stopped temporarily due to low voltage. It will resume running when the voltage restores to the normal level.
General| Type | Front Load |
|---|---|
| Capacity | 9 kg |
| Energy Efficiency Class | A+++ |
| Spin Speed | 1200 RPM |
| Dimensions (HxWxD) | 84 x 60 x 54 cm |
| Color | White |
| Spin Efficiency Class | B |
| Water Consumption per Cycle | 49 L |
| Noise Level (Spinning) | 72 dB |
| Noise Level (Washing) | 54 dB |
| Width | 60 cm |
| Depth | 54 cm |
| Height | 84 cm |
| Number of Programs | 15 |
| Water Consumption | 49 L |
To Next Page
