Beninca BE.CODE - FUNCTION MENU; MENU 1; MENU 2; MENU 3

12
thereceivermemory.
TheFathercodeoperatesindependentlyfrom
the presence of related Child codes.
Intheeventofnotparticularlycomplexinstal-
lations, it is possible to memorise Father codes
only,asindicatedinMenu2.
Aspecicradiocodesent tothe transmitter
correspondstoeachFathercode.Thisradio
codewilloccupyamemorylocation in the
receiver.
BE.TPUCHisabletostoreatotalof254codes,
which might be either Father or Child codes.
IMPORTANT: Never use codes with too sim-
ple or easily traceable number sequence.
FUNCTION MENU
Afteractivatingthe keypad, and typing the
accesspasswordfollowed by Enter, access
isenabledtotheFunctionMenu(2beepsare
heardfromthebuzzer).
BE.CODE awaits that one of the 9 Menu avail-
able is selected. During this dwell time, a beep
every0.5secisheard:
1 Change of access password for programming
menu
2TypinginofFathercode
3TypinginofChildcode
4 Erasing of Father/Child code
5 Activation of scalar counter
6CongurationMenuofoperation
7CongurationMenuofproximityswitch
8CheckMenuofthecodingtypeofamemo-
rised transmitter code
9EnableMenuofENTERbuttonforcoderep-
etition.
Press the desired menu button.
NOTE:
•Thekeypadisactivatedbypressinganykey..
•Autoshut-offis10seconds.Afterthisperiod
oftimethesystem must be switched on
again, as described above.
•Toexitaprogrammingmenuwithoutmak-
inganychanges,pressEnter,orwaitfor20
seconds(time-outtime).
•A possible programming error is indicated
with a long beep, BE.CODE then exits the
programming phase.
MENU 1
To customize the access password
Aftertypingkey1,the customizationof the
password phase is entered, indicated by 2
beepsfollowedbyaninterval.
- Typeinthenewpassword(6digit)andpress
ENTER.
- BE.CODEconrmsthetypingwith3beeps
followedbyaninterval.
- Typeinthenewpasswordoncemoreand
pressENTER.
- If the two digits are the same the password
isstoredinmemoryandthekeypadreturns
tostand-bymode.
MENU 2
Typing in of Father code
Aftertypingkey2,thecustomization of the
Fathercodeisentered,indicatedby2beeps
followedbyaninterval.TheFathercodecan
be composed of 1 to 9 digits.
-TypeinthedesiredFathercodeandpress
ENTER.3beeps,followedbyaninterval,are
heardtoconrmtheoperation.Thedeviceis
nowwaitingforacommandwhichspecies
thetypeofreceivercodingtobeusedforthe
codejusttypedin:
- Press1fortheRolling-codereceivers
- Press2fortheARCreceivers
- Press 3 for the Fixed-code receivers
MENU 3
Typing in of Child code
Aftertypingkey3,thecustomization of the
Fathercodeisentered,indicatedby2beeps
followedbyaninterval.
TheChild code can be composed of 1 to 9
digits.
- DigittheFathercode(followedbyENTER)to
whichtheChildcodeshouldbematched(it
willbetypedinafter).IfthetypedinFather
code is not valid, an error is shown. If the
code is valid, three beeps are heard and the
deviceawaitsthattheChildcodebetyped
in.
- TypetheChildcodeandthenpressENTER.
ThecodewillbematchedtotheFathercode
typedinbefore.TheChildcodewilltakethe
codingtypeandthetransmittedradiocode
from the Father code.