BFT RIGEL 6 - Expansion Board and Indicator Configurations; Expansion Board Input Configuration; Expansion Board Output Configuration; Traffic Light Indicator Settings

D812865 00100_04
48 - RIGEL 6
INSTALLATION MANUAL
Logic Denition Default
Cross out
setting
used
Optional extras
EXPI2
Conguration of
EXPI2 input
on input-output
expansion board.
1-3
0
0 Input congured as Start E command.
1 Input congured as Start I command.
2 Input congured as Open command.
3 Input congured as Close command.
4 Input congured as Ped command.
5 Input congured as Timer command.
6 Input congured as Timer Pedestrian command.
7 Input congured as Phot (photocell) safety.
8 Input congured as Phot op safety (photocell active during opening only).
9 Input congured as Phot cl safety (photocell active during closing only).
10
Input congured as Bar safety (safety edge).
11
Input congured as safety Bar OP, safety edge with inversion active only while opening, if while closing
the movement stops.
12
Input congured as safety Bar CL, safety edge with inversion active only while closing, if while opening
the movement stops.
EXPO1
Conguration of
EXPO2 output
on input-output
expansion board
4-5
11
0 Output congured as monostable Radio Channel.
1 Output congured as SCA (gate open light).
2 Output congured as Courtesy Light command.
3 Output congured as Zone Light command.
4 Output congured as Stair Light.
5 Output congured as Alarm.
EXPO2
Conguration of
EXPO2 output
on input-output
expansion board
6-7
11
6 Output congured as Flashing light.
7 Output congured as Latch.
8 Output congured as Magnetic lock.
9 Output congured as Maintenance.
10 Output congured as Flashing Light and Maintenance.
11 Output congured as Trac Light control with TLB board.
12
Not used
13
Output congured as Gate Status
14
Output congured as Bistable Radio Channel
15
Output congured as timed Radio Channel
TRAFFIC LIGHT
PREFLASHING
Trac light pre-
ashing
0
0 Pre-ashing switched o.
1 Red lights ash, for 3 seconds, at start of operation.
TRAFFIC LIGHT
RED LAMP
ALWAYS ON
Steadily lit red light 0
0 Red lights o when gate closed.
1 Red lights on when gate closed.
* Only active on FW > 1.12
Radio channel control conguration
CH logic= 0 - Control congured as Start E. Operation according to STEP-BY-STEP MOV. logic. External start for trac light control.
CH logic= 1 - Control congured as Start I. Operation according to STEP-BY-STEP MOV. logic. Internal start for trac light control.
CH logic= 2 - Control congured as Open.
The command causes the leaves to open.
CH logic= 3 - Control congured as Closed.
The command causes the leaves to close.
CH logic= 4 - Control congured as Ped.
The command causes the leaf to open to the pedestrian (partial) opening position. Operation according to STEP-BY-STEP. logic
Logica CH= 5- Control congured as STOP.
The command performs a STOP
CH logic= 6 - Control congured as AUX0. (**)
The control activates the AUX0 output
CH logic= 7 - Control congured as AUX1. (**)
The control activates the AUX1 output
CH logic= 8 -Control congured as AUX2. (**)
The control activates the AUX2 output
CH logic= 9 - Control congured as AUX3. (**)
The control activates the AUX3 output
CH logic= 10 - Control congured as EXPO1. (**)
The control activates the EXPO1 output
CH logic= 11 - Control congured as EXPO2. (**)
The control activates the EXPO2 output
(**) Active only if the output is congured as Monostable Radio Channel, Courtesy Light, Zone Light, Stair Light, Bistable Radio Channel or Timed Radio Channel.