To Next PageTo Next PageWhy does the fan in my Binder Oven not turn or turns too slowly?
If the fan in your Binder Oven doesn’t turn or turns too slowly, first check if the fan speed is set too low and set the fan speed to 100%. If the problem persists, contact Binder service.
Why is my Binder FED 400 Oven chamber without function, with only the green stand-by LED lit?
If your Binder Oven chamber has no function and only the green “stand-by” LED is lit, the chamber is likely in stand-by mode. Press the ON/OFF button until the display lights up.
How to fix temperature being too high in the Binder FED 400 Oven chamber?
If the temperature inside your Binder Oven chamber is too high and the red alarm pilot lamp of the safety device is lit, it indicates that safety device class 3.1 has responded. Check the temperature set-point and the settings of safety device class 3.1.
Why is the red alarm light lit on my Binder Oven?
If the red alarm pilot lamp of the safety device is lit on your Binder Oven, the safety device class 2 has likely turned off the chamber. Allow the chamber to cool down, then press the RESET button. Check the temperature set-point and the safety device class 2 settings, and select a suitable limit value if needed. For other potential causes, contact Binder service.
What to do if my Binder FED 400 Oven chamber doesn’t heat up, and the red heating control light in the display is lit?
If your Binder Oven chamber isn’t heating up but the red heating control light is lit, contact Binder service.
What to do if my Binder FED 400 chamber is heating permanently and the set-point is not held?
If your Binder Oven chamber is heating permanently and not maintaining the set-point, calibrate and adjust the controller. For other potential causes, contact Binder service.
Why does my Binder FED 400 chamber not heat up, and the red heating control light in the display is not lit?
If your Binder Oven chamber isn’t heating up and the red heating control light is off while the controller display is working, the timer may have run off. Program the timer or switch to continuous operation. If this doesn't solve the problem, contact Binder service.
What to do if my Binder FED 400 set-point temperature is not reached after the specified time?
If the set-point temperature in your Binder Oven isn't reached after the specified time, make sure the chamber door is completely closed. Also, inspect the door gasket and replace it if defective. Calibrate and adjust the controller and check the power supply to ensure it matches the required voltage (115V or 230V).
Information about legal aspects and liability for the operating manual.
Explains safety definitions, symbols, and signal word panels.
Details the positions of warning and service labels on the chamber.
Explanation of data and symbols found on the chamber's type plate.
Essential safety advice for installing and operating the chambers.
Defines the approved applications and limitations for the ovens.
Illustrates and lists the main components and controls of the FED oven.
Steps for unpacking, checking for completeness, and reporting transport damage.
Instructions for safely moving the chamber, including weight and method considerations.
Guidelines for intermediate storage, including temperature and humidity limits.
Requirements for the installation location and permissible environmental conditions.
Connecting the chamber to a computer using APT-COM™ software.
Details about the optional data logger for temperature measurement and recording.
Description of the optional HEPA filter for cleaning intake air.
Details on the optional feature for reduced vapor release and inert gas use.
Explanation of the inert gas connection option for gas-tight versions.
Description of the optional analog output for transmitting temperature data.
Information on recommended maintenance schedules and service procedures.
Procedures for cleaning and decontaminating the chamber to prevent damage and ensure safety.
Process for sending the chamber back for repair, including RMA requirements.
Guidelines for the disposal and recycling of transport packing materials.
Steps for safely shutting down and preparing the chamber for disposal.
Regulations for disposing of the chamber in Germany according to WEEE.
Guidelines for disposal in other EC countries, adhering to WEEE directive.
Instructions for environmentally friendly disposal in countries outside the EC.
Details on connecting the chamber to the power supply, including voltage and plug types.
Instructions for connecting an optional suction plant and its potential impact.
Step-by-step guide for powering on the chamber and initial display indications.
Explanation of how the heating status is indicated on the chamber's display.
How to adjust air change rates using the exhaust duct flap.
Setting temperature and fan speed values, including ramp function adjustments.
Managing continuous, timer, and delayed operation modes, including setting timer values.
A practical example illustrating how to program a temperature sequence.
Important operational notes and tips for using the controller functions.
Changing the temperature display between Celsius (°C) and Fahrenheit (°F).
Setting up temperature ramps for precise heating rate control.
Assigning unique addresses to chambers for network communication.
Choosing between delayed off, temp-controlled delayed off, and delayed on timer functions.
Configuring interface mode (Modbus/printer) and printer interval for data output.
Description and function of the Class 2 safety device for over-temperature protection.
Details on the optional Class 3.1 safety device for enhanced over-temperature protection.
Functionality of the optional audible alarm for over-temperature events.
Details on the factory calibration and adjustment procedures according to ISO 9001.
Explanation and calculation method for determining the chamber's usable internal volume.
Description of the fuse protection mechanisms for single-phase and three-phase devices.
Comprehensive technical specifications for various FED chamber models.
Overview of standard equipment and available optional accessories for the chambers.
List of available accessories and spare parts with their respective article numbers.
Formal declaration that the products comply with relevant EC directives and standards.
Documentation confirming the product's conformity with the GS mark of VDE.
Form for declaring safety and health information for returned chambers outside North America.
Form for requesting product return authorization for chambers in North America.
Declaration form for end-users regarding decontamination and hazard safety.
General
