What to do if my Binder 9010-0213 Oven chamber has no function at all?
If your Binder Oven chamber has no function, first check the connection to the power supply. If the connection is fine, check the chamber fuse and replace it if necessary. If the fuse responds again, contact Binder service.
What to do if my Binder Oven set-point temperature is not reached after the specified time?
If the set-point temperature in your Binder Oven isn't reached after the specified time, make sure the chamber door is completely closed. Also, inspect the door gasket and replace it if defective. Calibrate and adjust the controller and check the power supply to ensure it matches the required voltage (115V or 230V).
Why does my Binder Oven chamber not heat up, and the red heating control light in the display is not lit?
If your Binder Oven chamber isn’t heating up and the red heating control light is off while the controller display is working, the timer may have run off. Program the timer or switch to continuous operation. If this doesn't solve the problem, contact Binder service.
What to do if my Binder Oven chamber is heating permanently and the set-point is not held?
If your Binder Oven chamber is heating permanently and not maintaining the set-point, calibrate and adjust the controller. For other potential causes, contact Binder service.
What to do if my Binder 9010-0213 Oven chamber doesn’t heat up, and the red heating control light in the display is lit?
If your Binder Oven chamber isn’t heating up but the red heating control light is lit, contact Binder service.
Why is the red alarm light lit on my Binder 9010-0213 Oven?
If the red alarm pilot lamp of the safety device is lit on your Binder Oven, the safety device class 2 has likely turned off the chamber. Allow the chamber to cool down, then press the RESET button. Check the temperature set-point and the safety device class 2 settings, and select a suitable limit value if needed. For other potential causes, contact Binder service.
How to fix temperature being too high in the Binder 9010-0213 Oven chamber?
If the temperature inside your Binder Oven chamber is too high and the red alarm pilot lamp of the safety device is lit, it indicates that safety device class 3.1 has responded. Check the temperature set-point and the settings of safety device class 3.1.
Why is my Binder 9010-0213 Oven chamber without function, with only the green stand-by LED lit?
If your Binder Oven chamber has no function and only the green “stand-by” LED is lit, the chamber is likely in stand-by mode. Press the ON/OFF button until the display lights up.
Why does the fan in my Binder Oven not turn or turns too slowly?
If the fan in your Binder Oven doesn’t turn or turns too slowly, first check if the fan speed is set too low and set the fan speed to 100%. If the problem persists, contact Binder service.
Why are there deviations from the indicated heating-up times in my Binder 9010-0213?
Deviations from the indicated heating-up times in your Binder Oven can occur if the chamber is fully loaded. Reduce the load or allow longer heating-up times.
Power supply requirements, plugs, protective conductors, and circuit breaker recommendations.
Step-by-step guide for powering on and initiating the chamber.
Setting temperature and fan speed without temperature ramps.
Setting temperature and fan speed with temperature ramps.
Explanation of continuous and timer operation modes.
Guide on switching between continuous and timer modes.
Detailed steps to activate and use continuous operation mode.
Instructions on setting timer values for operation.
Explanation of Class 2 safety device, its function, and checking.
Explanation of optional Class 3.1 safety device, its function, and adjustment.
Guidelines on maintenance frequency and service requirements.
Procedures for cleaning and decontaminating the chamber.
Steps and recommended agents for cleaning interior/exterior surfaces.
Common temperature faults, causes, and required measures.
Common controller faults, causes, and required measures.
To Next Page
General
