What to do if my Binder VD 115 Oven chamber doesn’t heat up and shows a “Safety controller” alarm?
If the alarm message “Safety controller” appears on the controller display of your Binder oven, let the chamber cool down. Then, acknowledge the alarm on the controller. Check the settings of the temperature setpoint and safety controller value. If needed, select a suitable safety controller value.
Why are there deviations from the temperature set-point in the equilibrated state of my Binder oven?
If there are deviations from the temperature set-point in the equilibrated state of your Binder oven, use only the delivered expansion racks and do not change between aluminum and stainless steel racks.
Why are there deviations from the indicated heating-up times in my Binder VD 115 Oven?
If you notice deviations from the indicated heating-up times in your Binder oven, reduce the load in the oven or allow for longer heating-up times.
What to do if the controller on my Binder oven does not equilibrate to entered setpoints?
If the controller of your Binder oven does not equilibrate to entered setpoints, turn on temperature control. Turn on pressure control. If you are using MB2 controller, change to Fixed value operation mode if set-points were entered in Fixed value operation mode but the controller is in program operation mode.
What causes a Binder oven to not hold vacuum?
If the vacuum is not being held in your Binder oven, replace the door gasket, the safety glass panel, or the gaskets of the small flange connections.
Why is the chamber of my Binder VD 115 permanently turned off?
If the chamber of your Binder oven is permanently turned off, check the connection to the power supply. Ensure the power supply matches the voltage requirements of 115V or 230V. Also, check the chamber fuse.
How to fix a Binder VD 115 Oven when the chamber is heating permanently but the set-point is not maintained?
If your Binder oven chamber is heating permanently and the set-point isn't maintained, calibrate and adjust the controller.
Why is the set-point temperature not reached after the specified time in my Binder VD 115?
If the set-point temperature isn't reached in your Binder oven after the specified time, ensure the chamber door is completely closed. If the issue persists, the door gasket may be defective and require replacement. Also, calibrate and adjust the controller.
What to do if my Binder VD 115 Oven chamber doesn’t heat up and shows an “Overtemperature” alarm?
If your Binder oven displays an “Overtemperature” alarm and the chamber doesn’t heat up, allow the chamber to cool down. Acknowledge the alarm on the controller and restart the chamber. If the error occurs again, turn off the chamber.
Details the electrical connection requirements, including plug types, voltage, and fuses.
Details the operation and connection of the vacuum system for the drying oven.
Procedure for entering temperature and pressure set-points using the RD4 controller.
Procedure for entering set-points via the MB2 controller's menus or normal display.
Instructions for enabling or disabling the temperature control function.
Instructions for enabling or disabling the pressure control function.
Details the process of monitoring the drying cycle based on pressure changes.
Details user management, authorization levels, and password protection for MB2 controller.
Step-by-step guide for logging into the controller with user credentials.
Describes the electronic overtemperature safety controller and its protection functions.
Instructions for setting the safety controller mode and value for temperature protection.
Setting tolerance ranges and alarm delay times for temperature and pressure on RD4 controller.
Details the various alarm messages generated by the controller for equipment failures.
Steps for creating a new time-based program with set-points and durations.
Overview of program management functions like editing, copying, and deleting programs.
Guide for creating new weekly programs with time-based set-points.
Functions for managing week programs, including editing, copying, and deleting.
Provides basic troubleshooting steps for common chamber issues.
General| Power Supply | 230 V, 50/60 Hz |
|---|---|
| Control Type | Digital |
| Number of Shelves (standard/max) | 2/5 |
| Nominal Power | 2.5 kW |
| Temperature Range | 5 °C above ambient temperature to 300 °C |
| Interior Volume | 115 L |
| Power Consumption | 2.5 kW |
To Next Page
