Bissell 2066 Series User Manual

Bissell 2066 Series

20 pages

To Next Page

To Next Page

Page #1 background image

Loading...

Page #1 background image

PROHEAT 2X

®

REVOLUTION

™

PET PRO

_______________

USER GUIDE

2066 SERIES

Table of Contents

Questions and Answers:

D
David BrownAug 1, 2025
Why is my Bissell 2066 losing suction power?
- J
  James LeeAug 1, 2025
  There are several reasons why your Bissell Ultrasonic Jewelry Cleaner might be losing suction power: * The dirty tank may not be seated properly; pick it up and reseat it so it fits in the unit. * The dirty tank may be full; empty the dirty tank. * The rubber tab on the dirty water tank may not be sealed tight; check it and press firmly on all edges to secure it. * The accessory hose door may not be closed tightly; check it and make sure it is locked into place. * The nozzle may be clogged; use the nozzle clean out tool. * The brush roll cover may not be fully snapped into place; remove it and make sure you hear both buttons click into place.
M
Michael WelchAug 5, 2025
What to do if there is no spray through the hose & tool of my Bissell 2066?
- N
  Nicole HansonAug 5, 2025
  If you're not getting any spray through the hose and tool of your Bissell Ultrasonic Jewelry Cleaner, here's what you can check: 1. The hose to your machine is not primed or may have lost prime. With the machine off and unplugged, remove the nozzle from the foot. Place a ball point pen in the black cylinder next to the screw. When water bubbles up, remove the pen. Reassemble the nozzle and hose. Hold end of hose below water level in tank to prime. With the clean tank full of water, the machine OFF and RECLINED, press the CleanShot® button ON and wait for the CleanShot® to drain for a few seconds; This will re-prime the machine. 2. The clean water tank may be empty; refill it. 3. The clean tank may not be seated properly; turn the power OFF, remove, and reseat the clean water tank.
S
Sarah MoralesAug 9, 2025
Why does my Bissell Ultrasonic Jewelry Cleaner have no power?
- L
  Lori WilliamsAug 9, 2025
  If your Bissell Ultrasonic Jewelry Cleaner isn't turning on, consider these possibilities: * You might be mistaking the cleaning mode switch for the power button; press the red power button on the left side of the machine. * The outlet may not be active; try plugging in a different device to test the outlet.
R
Rebecca DiazAug 13, 2025
Why is there no spray through the CleanShot® of my Bissell 2066?
- L
  Lindsay MathewsAug 14, 2025
  If you're experiencing no spray through the CleanShot® feature on your Bissell Ultrasonic Jewelry Cleaner, consider the following: * The clean water tank may be empty; refill it. * The clean tank may not be seated properly; turn the power OFF, remove, and reseat the clean water tank. * The machine may not be reclined; press the recline pedal and bring the handle down to recline the machine. * The pump may have lost prime; with the machine off and unplugged, remove the nozzle from the foot. Place a ball point pen in the black cylinder next to the screw; when water bubbles up, remove the pen; reassemble the nozzle before cleaning again.
V
vrileyAug 18, 2025
How to fix reduced spray through foot of Bissell 2066?
- A
  Amanda MonroeAug 18, 2025
  If you're experiencing reduced or no spray through the foot of your Bissell Ultrasonic Jewelry Cleaner, it could be due to the following reasons: * The clean water tank may be empty; refill it. * The clean water tank may not be seated completely; turn the power OFF, remove, and reseat the tank.
R
Robert BarnesAug 22, 2025
What to do if the tank of my Bissell 2066 is leaking?
- A
  adam26Aug 22, 2025
  If the tank of your Bissell Ultrasonic Jewelry Cleaner is leaking: 1. Ensure the tank has the correct amount of water and formula. 2. Make sure the cap is twisted on tightly, hold your tank at an angle over a sink or drain, so any extra water can pour out of the space. 3. Wipe the tank dry with a cloth. Also, water may be caught in space between the tank and the tank’s handle.
J
jeffrey72Aug 27, 2025
What to do if CleanShot® continues to spray when my Bissell 2066 Ultrasonic Jewelry Cleaner is off?
- W
  waustinAug 27, 2025
  If the CleanShot® feature continues to spray when your Bissell Ultrasonic Jewelry Cleaner is turned off, the CleanShot® button is not in the “OFF” position. Press the CleanShot® button to turn it off. The button window will show the color red and a “O” symbol when it is in the off position.

Bissell 2066 Series Specifications

General

Type	Ultrasonic Jewelry Cleaner
Model	2066 Series
Cleaning Time	3 minutes
Power Supply	AC 120V, 60Hz
Power Consumption	35W

Summary

Important Safety Instructions

Quick Start Guide

Assembly

Step-by-step instructions for assembling the deep cleaner unit.

Cleaning Formulas

Filling Your Clean Water Tank

Cleaning Your Carpet

Deep Clean Mode

Express Clean Mode

Bare Floor Cleaning

Area Rug Cleaning

Cleaning with Hose & Tool

2-in-1 Pet Upholstery Tool

Empty Dirty Water Tank

Cleaning Machine After Use

Brush Roll & Nozzle Care

Replacing Belts & Brush Rolls

Replacing Belts & Brush Rolls (Continued)

Troubleshooting

Related product manuals

Preview: Bissell SPINWAVE 2307

Bissell SPINWAVE 2307

Bissell SPINWAVE 2315

Preview: Bissell CROSSWAVE 2554 Series

Bissell CROSSWAVE 2554 Series

Bissell Proheat 2x Revolution

Preview: PROHEAT 2X REVOLUTION 15484

PROHEAT 2X REVOLUTION 15484

PROHEAT 2X REVOLUTION 15503

Preview: Bissell CrossWave HF3

Bissell CrossWave HF3

Preview: Bissell CrossWave 1785

Bissell CrossWave 1785

Preview: Deep Clean Essential 9585

Deep Clean Essential 9585

PET STAIN ERASER 3181 Series

Preview: PET STAIN ERASER 3180 Series

PET STAIN ERASER 3180 Series

Preview: CROSSWAVE HYDROSTEAM 3515 Series

CROSSWAVE HYDROSTEAM 3515 Series