Bissell CROSSWAVE PET 2306 Series User Manual (English)

Other manuals for Bissell CROSSWAVE PET 2306 Series

Questions and Answers:

J
jamiedawsonAug 8, 2025
Why does my Bissell Vacuum Cleaner have a loss of suction power?
- J
  Jennifer CamposAug 8, 2025
  There are several reasons why your Bissell Vacuum Cleaner might be experiencing a loss of suction power: * The tanks may not be seated properly. Remove both tanks and reseat them to ensure they fit correctly. * The dirty tank may have reached its maximum capacity. Empty the dirty tank, making sure to use slow, back-and-forth cleaning passes. * The brush window might not be latched in place. Turn the power off, unplug the machine, and reinstall the brush window. * The debris channel in the foot could be clogged. Clean the channel with a paper towel. * The filter may be clogged by debris. Remove any debris clogging the filter screen and clean the filter.
S
sarahchapmanAug 13, 2025
Why is my Bissell Vacuum Cleaner not spraying?
- A
  apaceAug 13, 2025
  If your Bissell Vacuum Cleaner isn't spraying, it could be due to several reasons: * The clean water tank might be empty. Refill the tank. * The clean water tank might not be seated completely. Turn the power off, then remove and reseat the tank. * The system might not be fully primed. Hold the trigger for 10 to 15 seconds to prime it. * The brush window might not be latched in place. Turn the power off, unplug the machine, and reinstall the brush window. * You might not be holding the trigger continuously. Hold the trigger while using the machine. * The spray tips on the foot could be clogged. Use a pin to clean the spray tips located underneath the brush roll window.
A
Aaron KaufmanAug 18, 2025
What to do if my Bissell CROSSWAVE PET 2306 brush roll is not turning?
- S
  sharon15Aug 18, 2025
  If the brush roll on your Bissell Vacuum Cleaner isn't turning, consider these potential causes: * The brush roll might not be installed properly. Turn the power off, unplug the machine, and follow the instructions to replace the brush roll. * The machine might be standing upright. Recline the machine to activate the brush roll. * An obstruction might be preventing the brush roll from turning. Turn the power off, unplug the machine, remove the brush window and brush roll, and clean any hair or string from the brush ends.
C
cooktanyaAug 23, 2025
What to do if my Bissell CROSSWAVE PET 2306 machine won’t turn on?
- L
  Lisa TurnerAug 23, 2025
  If your Bissell Vacuum Cleaner won't turn on, it could be due to the following reasons: * An obstruction may have stopped the brush roll and shut down the machine. Unplug the machine to reset the system. While it's unplugged, remove the brush window and brush roll, cleaning any hair or string from the brush ends. * The handle might not be properly inserted into the body of the machine. Remove the handle and re-insert it, pushing down until you hear a 'click'.
K
Kimberly CookAug 28, 2025
Why is my Bissell CROSSWAVE PET 2306 Vacuum Cleaner machine leaking?
- A
  Aaron AshleyAug 28, 2025
  If your Bissell Vacuum Cleaner is leaking, it might be because the cap of the clean water tank isn't closed properly. Remove the clean water tank and re-apply the cap securely.
J
James MendozaSep 2, 2025
How to prevent my Bissell CROSSWAVE PET 2306 machine from streaking?
- A
  Amanda DanielSep 2, 2025
  If your Bissell Vacuum Cleaner is leaving streaks, it could be due to these reasons: * Too much water is being applied. Go over the area again without spraying water. * Previous floor care products were used. Contact the product manufacturer for instructions on how to remove them.