Why does the Black & Decker Drill battery pack not charge?
If the battery pack for your Black & Decker Drill won't charge, ensure the charger is properly plugged into a working outlet. Also, the surrounding air temperature might be too hot or too cold. Move the charger and battery pack to an area where the surrounding air temperature is above 40 degrees F (4.5ºC) or below 105 degrees F (40.5ºC).
Why is my Black & Decker Power Screwdriver battery pack not charging?
If the battery pack for your Black & Decker Power Screwdriver isn't charging, consider these possibilities: * The battery pack may not be fully inserted into the charger; insert it until the LED illuminates. * The charger might not be plugged into a working outlet; ensure it's properly plugged in. * The surrounding air temperature could be too hot or too cold; move the charger and battery pack to a location with a temperature between 40 degrees F (4,5°C) and 105 degrees F (+40,5°C).
What to do if my Black & Decker BDCDD12 shuts off abruptly?
If your Black & Decker Drill shuts off abruptly, it might be due to the battery pack reaching its maximum thermal limit or being out of charge. Allow the battery pack to cool down, then place it on the charger and allow it to charge completely.
Why won't my Black & Decker Power Screwdriver start?
Your Black & Decker Power Screwdriver might not start due to several reasons: * The battery pack may not be installed properly; check its installation. * The battery pack might not be charged; verify the charging requirements. * Internal components could be too hot; allow the tool to cool down. * The brushes may be worn out; have them replaced by an authorized Black & Decker service center.
What to do if my Black & Decker Power Screwdriver shuts off abruptly?
If your Black & Decker Power Screwdriver shuts off abruptly, it could be due to: * The battery pack reaching its maximum thermal limit; allow it to cool down. * The battery being out of charge; place it on the charger to recharge.
How to improve dust collection on my Black & Decker Power Screwdriver?
If dust is not being collected by your Black & Decker Power Screwdriver, check the following: * Ensure the sandpaper holes align properly. Use sandpaper with the appropriate hole configuration. * The dust bag may be full. Separate the dust bag and gently shake or tap to empty it.
General| Soft grip | Yes |
|---|---|
| Chuck type | Keyless |
| Product design | Pistol grip drill |
| Number of gears | 2 |
| Torque settings | 11 |
| Sound power level | 74 dB |
| Chuck capacity (max) | 10 mm |
| Chuck capacity (min) | 1 mm |
| Sound pressure level | 63 dB |
| Idle speed (1st gear) | 550 RPM |
| Drilling diameter in wood (max) | 25 mm |
| Maximum torque (hard applications) | 26 N⋅m |
| Maximum torque (soft applications) | 12.5 N⋅m |
| Vibration emission | 2.5 m/s² |
| Product color | Black, Orange |
| Number of batteries included | 1 pc(s) |
| Power source | Battery |
| Charging time | 180 min |
| Battery voltage | 10.8 V |
| Battery capacity | 1.5 Ah |
Read all safety warnings and instructions to prevent electric shock, fire, and injury.
Keep work area clean and well-lit, avoid explosive atmospheres, keep children and bystanders away.
Match plugs, avoid body contact with grounded surfaces, do not expose to rain or wet conditions.
Stay alert, use PPE, prevent unintentional starting, don't overreach, dress properly, use dust extraction.
Proper tool usage, maintenance, battery charging, and care to ensure safety and longevity.
Tool servicing, specific drill safety, safety of others, residual risks, and vibration information.
Tool labels, key features, and general assembly notes for initial setup and understanding.
Safety guidelines for batteries and chargers, including electrical safety during charging.
Step-by-step instructions and warnings for charging the battery pack before first use.
Procedures for inserting and removing the battery pack from the tool.
Explains trigger, reversing button, torque control, keyless chuck, and drilling/screwdriving modes.
Provides tips for efficient drilling and screwdriving techniques for best results.
To Next Page
