Black & Decker BDXBTVAR150

Questions and Answers

R
Ryan StevensonAug 5, 2025
Why is my Black & Decker Water Pump not working?
- D
  Dan BowmanAug 5, 2025
  Your Black & Decker Water Pump might fail due to several reasons: an air leak (check suction piping and valve glands, secure the lid on the pump strainer pot, and ensure the lid gasket is in place), insufficient water (verify the water level to ensure the skimmer isn't drawing air), a clogged pump strainer gasket (clean the pump strainer pot), or a defective pump strainer gasket (replace the gasket).
K
Kelly MedinaAug 9, 2025
What to do if my Black & Decker BDXBTVAR150 runs then stops?
- K
  Karl GarciaAug 9, 2025
  If your Black & Decker Water Pump runs and then stops, it might be due to an over-temperature or over-current fault. Ensure the back of the pump is free from dirt and debris to prevent overheating. For an over-current fault, use compressed air to clean the pump; it will automatically restart after one minute.
M
Mark WallaceAug 14, 2025
Why is my Black & Decker Water Pump so noisy?
- F
  fperezAug 14, 2025
  A noisy Black & Decker Water Pump could be caused by debris in contact with the fan (ensure the back of the pump is free from dirt and debris), debris in the strainer basket (clean the strainer basket), or loose mounting (check that the mounting bolts of the pump are tight).
K
Kimberly GriffithAug 19, 2025
Why Black & Decker Water Pump runs without flow?
- K
  Kristina CruzAug 19, 2025
  If your Black & Decker Water Pump runs without flow, the impeller might be loose (check that the pump is spinning by looking at the fan on the back of the Variable Speed Pump and that the pump impeller is correctly installed), there could be an air leak (check plumbing connections and verify they are tight), or the plumbing might be clogged or restricted (check for blockage in the strainer or suction side piping, and in the discharge piping, including a partially closed valve or dirty pool filter).
B
brittany75Aug 25, 2025
How to fix reduced capacity in Black & Decker BDXBTVAR150?
- S
  Steven BarnesAug 25, 2025
  Reduced capacity in your Black & Decker Water Pump can stem from air pockets or leaks in the suction line (check suction piping and valve glands, and secure the lid on the pump strainer pot), a blocked impeller (turn off power and clean debris from the impeller), or a clogged pump strainer (clean the suction trap).
L
Laura HoweAug 29, 2025
What to do if Black & Decker BDXBTVAR150 Water Pump fails to start?
- B
  Benjamin SparksAug 29, 2025
  If your Black & Decker Water Pump fails to start, the issue might be due to missing mains voltage (replace the fuse, reset the breaker/GFCI), a locked pump shaft (check if the pump can be rotated by hand and remove any blockage), or a damaged pump shaft (replace the pump).

Summary

Pool Pump Safety Instructions

Risk of Electric Shock

Details specific electrical shock hazards and necessary precautions.

Pool Pump Entrapment Hazards

Pool Pump Pressure Hazards

Pool Pump General Information

Pump Manual Introduction

Overview of the manual's purpose and the pump's operational capabilities.

Variable Speed Pump Overview

Description of the pump's design and suitability for pools and spas.

Pump Controller and Speed Settings

Explanation of the variable speed motor, its control, and energy efficiency.

Black+Decker Pump Control Panel

Pump Size and Installation Dimensions

Pump Base Adjustment Guide

Variable Speed Pump Specifications

Pump Package Contents List

Pool Pump Installation Guide

Pump Installation Location Requirements

Guidelines for choosing a suitable installation site for the pump.

Pool Pump Piping Installation

Recommendations for suction and return piping installation for optimal performance.

Pump Plumbing Fittings and Valves

Pump Electrical Installation Requirements

Pump Wiring and Grounding Instructions

Operating the Variable Speed Pump

Setting the Pumps Internal Clock

Steps to set the internal clock for pump scheduling and operation.

Understanding the Default Pump Schedule

Explanation of the pre-programmed daily pump operation schedule.

Pump Priming Procedure

Guidance on setting the initial speed for pump priming after installation.

Programming Custom Pump Schedules

Pump Speed Priority Settings

Pump Operation While Running

Pool Pump Maintenance Guide

Strainer Basket Inspection and Care

Location and importance of cleaning the pump strainer basket.

How to Clean the Pump Strainer Basket

Step-by-step instructions for cleaning the pump strainer basket.

Pump Winterization Procedures

Procedures to protect the pump from freeze damage during winter storage.

Pool Pump Servicing and Repair

Motor Care: Heat, Dirt, and Moisture

Guidelines for protecting the motor from heat, dirt, and moisture.

Replacing the Pump Shaft Seal

Information about the shaft seal and when it needs replacement.

Pump Disassembly Instructions

Detailed steps for disassembling the pump's rear subassembly.

Pump Reassembly Steps

Pump Restart and Priming Guide

Pool Pump Troubleshooting Guide

Troubleshooting Pump Failure and Priming

Common issues and solutions for pump failure and priming problems.

Troubleshooting Reduced Capacity and Starts

Diagnosing low performance and pump start-up issues.

Troubleshooting Operation Cycles and Noise

Addressing pump operation cycles and noise generation.

Troubleshooting No Flow and System Errors

Black+Decker Pump Replacement Parts

Variable Speed Pump Performance Data

Pool Pump Limited Warranty Information

Black & Decker BDXBTVAR150 Specifications

General

Model	BDXBTVAR150
Category	Water Pump
Power Source	Electric
Voltage	120V
Flow Rate	1500 GPH
Max Lift Height	25 ft
Type	Submersible
Horsepower	0.25 HP
Hose Diameter	1-1/4 inch