Why is my Black & Decker PW1500SP Water Pump so noisy?
If your Black & Decker Water Pump is excessively noisy, the water might be too hot. Try reducing the water temperature according to the technical data.
Why is my Black & Decker Pressure Washer so noisy?
If your Black & Decker Pressure Washer is making excessive noise, the water may be too hot. Reduce the water temperature.
What to do if my Black & Decker Pressure Washer TSS version has no water delivery when the gun trigger is depressed?
If you have a TSS version of the Black & Decker Pressure Washer and there's no water delivery when you depress the gun trigger (with the supply hose connected), the nozzle is likely clogged. Clean the nozzle.
Why does my Black & Decker Pressure Washer motor sound but fail to start?
If your Black & Decker Pressure Washer motor makes a sound but doesn't start, first verify that the voltage of the mains power supply line matches what's indicated on the appliance's plate. Also, check the characteristics of any extension cable you're using, as voltage loss due to the extension cable could be the issue.
What to do if my Black & Decker Pressure Washer pressure drops during use?
If you notice the pressure dropping during use of your Black & Decker Pressure Washer, consider these potential causes: * If you're using an external tank for water intake, try connecting the appliance to the mains water supply instead. * If the intake water is too hot, reduce the temperature. * A clogged nozzle can also cause pressure drops; clean the nozzle.
Why is my Black & Decker Water Pump leaking oil?
If you observe oil leakage from your Black & Decker Water Pump, this indicates that the seals are worn. Contact your nearest Authorized Service Centre to have them replaced.
Why Black & Decker PW1500SP (TSS versions) has no water delivery when gun trigger is depressed?
If your TSS version of the Black & Decker Water Pump isn't delivering water when the gun trigger is depressed and the supply hose is connected, the nozzle might be clogged. Try cleaning the nozzle.
How to fix Black & Decker PW1500SP Water Pump when no detergent is taken in?
To resolve the issue of no detergent being taken in by your Black & Decker Water Pump, ensure the adjustable nozzle is not on a high-pressure setting; set it to the "-" setting. If the detergent is too dense, dilute it with water. Also, if you're using a high-pressure hose extension, try fitting the original hose. If there are deposits or restrictions in the detergent circuit, flush it with clean water and eliminate any restrictions. If the problem persists, contact an Authorized Service Centre.
Why Black & Decker PW1500SP (TSS versions) motor starts even with gun trigger released?
If your TSS version of the Black & Decker Water Pump motor starts even when the gun trigger is released, the nozzle might be clogged and require cleaning. Alternatively, the high-pressure system or pump hydraulic circuit may not be watertight, in which case you should contact your nearest Authorized Service Centre.
Why Black & Decker PW1500SP Water Pump does not reach working pressure?
If your Black & Decker Water Pump isn't reaching working pressure, several factors could be at play. First, ensure the water supply tap is fully open to maximize water supply pressure. Check the tightness of hose fittings to prevent air from being sucked into the system. If there's air in the pump, switch off the appliance and repeatedly depress and release the gun trigger until a steady water flow is achieved, then switch the appliance back on. Also, verify that the adjustable nozzle is correctly positioned. If none of this helps, the nozzle may be worn and needs replacement, or the water filter could be fouled and requires cleaning. Lastly, the thermostatic valve may have tripped; in that case, wait for the correct water temperature to be restored.
General| Model | PW1500SP |
|---|---|
| Power Source | Electric |
| Voltage | 120V |
| Cord Length | 35 ft |
| Thermal Protection | Yes |
| Power | 1500 watts |
| Type | Pressure Washer |
| Horsepower | 2 HP |
To Next Page
