Black & Decker PW1700SPM

Questions and Answers

F
freyantonioAug 16, 2025
Why Black & Decker Water Pump does not reach working pressure?
- J
  James KnappAug 16, 2025
  If your Black & Decker Water Pump isn't reaching working pressure, several factors could be at play. First, ensure the water supply tap is fully open to maximize water supply pressure. Check the tightness of hose fittings to prevent air from being sucked into the system. If there's air in the pump, switch off the appliance and repeatedly depress and release the gun trigger until a steady water flow is achieved, then switch the appliance back on. Also, verify that the adjustable nozzle is correctly positioned. If none of this helps, the nozzle may be worn and needs replacement, or the water filter could be fouled and requires cleaning. Lastly, the thermostatic valve may have tripped; in that case, wait for the correct water temperature to be restored.
M
Micheal MillerAug 19, 2025
Why does the pressure drop during use of my Black & Decker Water Pump?
- M
  Melissa CoxAug 19, 2025
  If the pressure drops during the use of your Black & Decker Water Pump, it might be due to several reasons. If you're using an external tank for water intake, try connecting the appliance to the mains water supply instead. Also, check the temperature of the intake water, as it might be too hot and needs to be reduced. A clogged nozzle or a dirty intake filter (L) could also be the cause. In that case, you should clean the nozzle or clean the filter (L).
C
cynthiahowardAug 22, 2025
What to do if Black & Decker Water Pump motor sounds but fails to start?
- M
  Michael BenderAug 22, 2025
  If your Black & Decker Water Pump motor sounds like it's working but won't start, the issue might stem from an insufficient power supply. Verify that the voltage of the mains power supply line matches the specifications on the appliance's plate. Voltage loss due to an extension cable could also be the culprit, so check the cable's characteristics. If the appliance hasn't been used for a long time or you suspect problems with the TSS device, it's best to contact your nearest Authorized Service Centre for assistance.
K
kpalmerAug 26, 2025
What to do if Black & Decker PW1700SPM Water Pump motor fails to start?
- S
  sarah84Aug 26, 2025
  If your Black & Decker Water Pump motor fails to start, first ensure that the plug is firmly inserted into the socket and that the mains voltage supply is present. If the issue persists, and you suspect problems with the TSS device or the appliance hasn't been used for a long period, contact your nearest Authorized Service Centre. In models with this feature, you can also try unjamming the motor from the hole at the rear of the appliance using the tool (L).
K
Katrina CoxAug 28, 2025
Why is my Black & Decker PW1700SPM Water Pump leaking water?
- B
  Bradley PattersonAug 28, 2025
  If you notice water leakage from your Black & Decker Water Pump, this could be due to worn seals or a tripped safety valve. In both cases, it's recommended to contact an Authorized Service Centre to have the seals replaced or to address the safety valve issue.
D
Dylan HillAug 31, 2025
Why is my Black & Decker PW1700SPM so noisy?
- G
  Glenn KellerAug 31, 2025
  If your Black & Decker Water Pump is excessively noisy, the water might be too hot. Try reducing the water temperature according to the technical data.
S
Samantha MillerSep 3, 2025
Why Black & Decker PW1700SPM Water Pump (TSS versions) motor starts even with gun trigger released?
- R
  Raymond MillerSep 3, 2025
  If your TSS version of the Black & Decker Water Pump motor starts even when the gun trigger is released, the nozzle might be clogged and require cleaning. Alternatively, the high-pressure system or pump hydraulic circuit may not be watertight, in which case you should contact your nearest Authorized Service Centre.
D
David HarrisSep 6, 2025
How to fix Black & Decker PW1700SPM Water Pump when no detergent is taken in?
- A
  Anthony Thompson PhDSep 7, 2025
  To resolve the issue of no detergent being taken in by your Black & Decker Water Pump, ensure the adjustable nozzle is not on a high-pressure setting; set it to the "-" setting. If the detergent is too dense, dilute it with water. Also, if you're using a high-pressure hose extension, try fitting the original hose. If there are deposits or restrictions in the detergent circuit, flush it with clean water and eliminate any restrictions. If the problem persists, contact an Authorized Service Centre.
P
Phillip BrownSep 9, 2025
Why Black & Decker Water Pump (TSS versions) has no water delivery when gun trigger is depressed?
- V
  vnealSep 9, 2025
  If your TSS version of the Black & Decker Water Pump isn't delivering water when the gun trigger is depressed and the supply hose is connected, the nozzle might be clogged. Try cleaning the nozzle.
W
Whitney YangSep 12, 2025
Why is my Black & Decker PW1700SPM leaking oil?
- A
  April PalmerSep 12, 2025
  If you observe oil leakage from your Black & Decker Water Pump, this indicates that the seals are worn. Contact your nearest Authorized Service Centre to have them replaced.

Black & Decker PW1700SPM Specifications

General

Form factor	Upright
Power source	-
Water filter	Yes
Product color	Black, Red
Maximum flow rate	370 l/h
Working pressure (max)	130 bar
Power consumption (typical)	1700 W