Black & Decker VEC1045BD User Manual

VEHICLE POWER SYSTEM
POWER INVERTER
200/400/750 WATT
VEC1045BD / VEC1046BD / VEC1047BD
USER’S MANUAL
& WARRANTY INFORMATION
II
II
MM
MM
PP
PP
OO
OO
RR
RR
TT
TT
AA
AA
NN
NN
TT
TT
SS
SS
AA
AA
FF
FF
EE
EE
TT
TT
YY
YY
II
II
NN
NN
FF
FF
OO
OO
RR
RR
MM
MM
AA
AA
TT
TT
II
II
OO
OO
NN
NN
,,
,,
SS
SS
AA
AA
VV
VV
EE
EE
TT
TT
HH
HH
EE
EE
SS
SS
EE
EE
II
II
NN
NN
SS
SS
TT
TT
RR
RR
UU
UU
CC
CC
TT
TT
II
II
OO
OO
NN
NN
SS
SS
TO REDUCE THE RISK OF INJURY, USER MUST READ AND UNDERSTAND
THIS INSTRUCTIONAL MANUAL. THIS MANUAL CONTAINS IMPORTANT
INFORMATION REGARDING THE OPERATION AND WARRANTY OF THIS
PRODUCT. PLEASE RETAIN FOR FUTURE REFERENCE.
www.vectormfg.com
4140 S.W. 30th Ave., Ft. Lauderdale, FL 33312
Toll Free: (800) 618-5178
8
Fault Protection Code and Troubleshooting Guide
INVERTER POWER SWITCH TURNED ON
SPECIFICATIONS
Power Inverter Model VEC1045BD VEC1046BD VEC1047BD
Maximum Continuous Power: 200 watts 400 watts 750 watts
Surge Capacity: 400 watts 800 watts 1500 watts
Input Voltage: 12.8 volts
Output Voltage: Approx. 115 volt AC RMS 60 Hz
Low Voltage Alarm: 11 volts DC ± 0.3 volt DC
Low Voltage Shutdown: 10.5 volts DC ± 0.3 volt DC
Thermal Shutdown: Automatic
Wave Form: Modified Sine Wave (MSW)
Output Connection: North American Standard Receptacles
Input Fuses: Internal
Input Cables: Battery cable with ring connector
Additional Protection: Overload, over voltage, overheating
Trouble/Indication Possible Cause Suggested Remedy
No AC output — DC input is out of range Check battery voltage.
(red LED lit
Excessive load — Turn unit off. Reduce the load,
thermal shutdown wait for the inverter to cool
down, then turn the unit on
again.
No AC output — Fuse(s) open Check DC input — fuse(s) in
green LED not lit vehicle. Replace the fuse with
one of the same type and rating
if necessary.
Low battery alarm Low battery voltage Recharge battery. Remove
sounds continuously load from the inverter while
recharging battery.
Bad connection or wiring Tighten all DC connections.
Motorized power tool Excessive start-up load If appliance does not start,
will not start appliance is drawing
excessive voltage and
will not work with inverter.
Motorized power tool Purely inductive load Make the load not purely
does not operate at inductive. Operate an
correct speed incandescent lamp at the
same time as motor.
Television/Radio Snow in picture, Keep inverter and antenna
interference “buzzing” sound distant from each other. Use
shielded antenna. Connect
antenna to amplifier.
VEC1045_46_47_BD_Manual 4/28/05 5:16 PM Page 8

Black & Decker VEC1045BD Specifications

General

Brand	Black & Decker
Model	VEC1045BD
Category	Inverter
Language	English

Summary

Fault Protection Code and Troubleshooting Guide

Specifications

User's Manual & Warranty Information

Important Safety Information

Key safety instructions and warnings for inverter operation.

Important Safety Instructions

Warnings

Critical warnings to reduce risk of fire, shock, explosion, or injury.

Cautions

Important cautions to prevent damage to the inverter and ensure safe operation.

Important Cable Information

Guidance on selecting appropriate cables for power loss and battery life.

Two Year Limited Warranty Program

Introduction

Features

How This Inverter Works

Principle of Operation

Explains the two-stage DC-to-DC and inverter conversion process.

The Power Inverter Output Waveform

Describes the modified sine wave output and its suitability for devices.

Operating Instructions

Power Source Requirements

Specifies voltage and current needs for the power source.

Connection to Power Source

Details how to connect the inverter to a 12V DC power source.

Run Times

Information on how long the inverter can operate based on battery capacity.

Rated Versus Actual Current Draw of Equipment

Guidance on matching equipment power draw to inverter capabilities.

Protective Features of the Inverter

Details the inverter's internal protection mechanisms against hazards.

Connecting to a Power Source Using the Provided Cables

Step-by-step guide for connecting the inverter via accessory plug or clips.

Direct Hardwiring to Power Source

Instructions for hardwiring the inverter directly to a DC power source.

Connection To Load

How to connect electrical equipment to the inverter's AC outlets.

Operating Tips

Recommendations for optimal inverter placement and operating environment.

Rechargeable Devices

Notes on compatibility of certain rechargeable devices with modified sine wave.

Care and Maintenance

Storage

Guidelines for ideal storage temperature and conditions.

Fuse Replacement

Information and warnings regarding internal fuse replacement.

Troubleshooting

Common Audio/Visual Problems

Addresses buzzing in audio systems and television interference.

Television Interference

Provides corrective measures for TV signal interference.