ENGLISH
(Original instructions)
7
tions, etc.
♦ Ensure that the appliance is level with respect to the
oor.
♦ The appliance requires suitable ventilation in order to
work properly. Leave a space of 50cm between walls or
other obstacles.
♦ Do not cover or obstruct any of the openings of the
appliance.
♦ Do not cover or obstruct the sides of the appliance,
and leave a minimum space of 50cm front other walls,
ceiling.
♦ The plug must be easily accessible so it can be discon-
nected in an emergency.
♦ To achieve the highest efciency from the appliance it
should be situated in a place where the atmospheric
temperature is between 12 and 32ºC.
♦ Ensure that the extraction pipe remains in a horizontal
position.
♦ Do not add new sections to the extraction tube provided,
as it could cause the appliance to malfunction.
♦ Assemble the hose adaptor. Don´t push too hard to
prevent damage.
♦ Assembly of the exhaust hose
♦ Lengthen one head of the hose, screw it into the unit
anti-clockwise.
♦ The same way to connect the hose to the assembled
adaptor( At least three circles)
Assembling the battery/s
♦ Caution: During the handling of batteries, do not touch
both poles at the same time, as this will provoke the
partial discharge of the stored energy therefore affecting
longevity.
♦ Remove the cover of the battery compartment.
♦ Check that the plastic covering that protects the battery
has been removed (some batteries are sold with a
protective covering)
♦ Put the battery in its compartment, respecting the
polarity.
♦ Replace the cover of the battery compartment.
♦ It is essential that the batteries should always be the
same kind and the same charge. Never mix alka-
line batteries with normal one (Carbon-Zinc) and/or
rechargeable ones.
Installation of window kits.
♦ Partially open the window and then x the window kits
to the window
♦ The window kits can be installed on most normal and
vertical windows, and it is adjustable. (Fig.1)
♦ Fix the other end of the heat-exhausted hose to the
air-outlet window kit. (Fig.2)
INSTRUCTIONS FOR USE
Before use:
♦ Remove the appliance’s protective lm.
♦ Before using the unit, please keep it upright at least 2
hours.
Use:
♦ Unroll the cable completely before plugging it in.
♦ Connect the appliance to the mains.
♦ You will hear a beep, the unit is in stand by status.
♦ When press the ON/OFF button, the unit will enter in
cooling mode (setting temperature 24ºC), high speed
fan.
♦ Press again , unit will shut off and play shut off beep.
♦ Press the MODE button to choose Cooling, Heating
(only for the model BXAC12000E) Fan or dehumidifying
mode.
Fan speed:
♦ Under the cooling and the fan mode, the speed goes as
follow:
♦ Low Fan (F1)→Middle Fan (F2)→High Fan (F3)→Low
Fan (F1)
♦ Under the dehumidifying mode, fan is working in low
speed.
Timer function:
♦ The appliance’s operating time can be controlled.
♦ To program the operating time simply select it using
pressing the timer icon.
♦ Timer icon will ash “88” area indicates 24:00.
♦ You can set your time through UP and DOWN buttons.
♦ The HOUR number will change from 1-24h.
♦ Auto-shut-off timer is only available when the unit on.
♦ Auto-run timer is only available when the unit is off.
♦ Up and Down button can set temperature and timer.
Swing:
♦ Press this button to control the swing function.
To Next Page
Loading...
Need help?
General
