BNF Blade 300 X - User Manual

Questions and Answers

N
Norma JohnsonAug 15, 2025
How to fix a BNF Blade 300 X Toy helicopter tail that spins out of control?
- C
  Crystal MurphyAug 15, 2025
  If the tail of your BNF Toy helicopter spins out of control, you should first ensure that the rudder control and rudder sensor are operating in the correct direction. Next, check the rudder servo for damage and replace it if necessary. Also, verify that the rudder control arm has adequate travel and adjust if needed. Finally, make sure the tail drive belt tension is adjusted correctly.
M
Michael BlankenshipAug 18, 2025
What to do if AR7200BX of BNF Blade 300 X helicopter will not initialize?
- E
  Erica RossAug 18, 2025
  If the AR7200BX on your BNF Toy helicopter won't initialize, there are a few things to check. Make sure the helicopter isn't moved during initialization; if it's windy, lay the helicopter on its side. Ensure the transmitter is powered on. Also, center the elevator, aileron, and rudder controls, and make sure the throttle is at idle.
M
Mary WestAug 21, 2025
What to do if BNF Blade 300 X Toy helicopter throttle is not responding?
- R
  Russell RandallAug 22, 2025
  If your BNF Toy helicopter responds to other controls but not the throttle, there are several things you can check. Ensure the throttle stick and throttle trim are at their lowest settings. Verify that the transmitter is in normal mode and throttle hold is off. Check that the motor wires are properly connected to the ESC and inspect them for any damage. Also, make sure the flight battery is adequately charged, and if necessary, power down the helicopter and reverse the throttle channel on the transmitter.
A
aprilperezAug 25, 2025
Why my BNF Blade 300 X helicopter won't link to the transmitter after binding?
- M
  millerjordanAug 26, 2025
  If your BNF Toy helicopter doesn't link to the transmitter after binding, it could be due to a couple of reasons. If you're using a ModelMatch™ radio, the helicopter may be bound to a different model memory; in that case, disconnect the flight battery, select the correct model memory on the transmitter, and reconnect the flight battery. Also, check if the flight battery or transmitter battery charge is too low, and if so, replace or recharge the batteries.
M
Megan MccartyAug 28, 2025
Why is my BNF Blade 300 X Toy helicopter lacking power?
- T
  timothyjoyceAug 28, 2025
  If your BNF Toy helicopter is lacking power, several factors could be responsible. Ensure the flight battery is fully charged, and if it's old or damaged, replace it. Also, make sure the flight battery cells are balanced by fully charging the battery and allowing the charger time to balance them. Check all servos and the helicopter motor for any damage, as excessive current might be drawn through the BEC. Finally, verify that the tail drive belt tension is correct; see "Checking Tail Drive Belt Tension" in this manual.
O
ogillSep 1, 2025
What to do if my BNF Toy helicopter will not lift off?
- M
  Mary Reilly DVMSep 1, 2025
  If your BNF Toy helicopter won't lift off, several issues could be the cause. Ensure the main rotor head is spinning clockwise, referring to the motor control test if needed. Verify that the transmitter settings, specifically the throttle and pitch curve settings, are correct. Make sure the flight battery is fully charged. Finally, check that the main rotor blades are installed correctly, with the thicker side as the leading edge.
R
Rachel ChristensenSep 4, 2025
Why does my BNF Toy helicopter wobble in flight?
- N
  Nicholas BradySep 4, 2025
  If your BNF Toy helicopter wobbles in flight, it could be due to several reasons. The cyclic gain might be too high, so try decreasing Dial 1 on the AR7200BX. The head speed might be too low, so increase it via your transmitter settings or use a freshly charged flight pack. Additionally, the dampers might be worn, so consider replacing the main rotor head dampers.
L
Lauren BennettSep 7, 2025
Why won't the flight battery of my BNF Blade 300 X charge?
- S
  Steven MartinezSep 7, 2025
  If your BNF Toy flight battery won't charge, first ensure that the input voltage to the charger is between 11.5–15V DC with a minimum 3A current. Then, check the battery balance tab to make sure the balance tab wires are fully seated in the balance plug. If any cell voltage drops below 3V, the battery is damaged and must be replaced.
P
Patrick ScottSep 12, 2025
Why won't my BNF Toy helicopter bind to the transmitter?
- J
  Jerry McmahonSep 12, 2025
  There are several reasons why your BNF Toy helicopter might not be binding to the transmitter. It could be due to a low flight battery or low transmitter battery voltage; in this case, fully charge or replace the flight battery and/or transmitter batteries. Another reason could be that the AR7200BX is not in bind mode; ensure the bind plug is connected to the AR7200BX BND/DAT port. The transmitter might not be in bind mode, so refer to your transmitter's instruction manual for binding instructions. Finally, the transmitter might be too close to the helicopter during the binding process. If that's the case, power off the transmitter, move it further away from the helicopter, disconnect and reconnect the flight battery to the helicopter, and then follow the binding instructions.