BOMCO F-1300 - User Manual

Questions and Answers

A
Amber SalazarAug 12, 2025
Why is my BOMCO Water Pump diesel overloaded?
- H
  Harold BeasleyAug 13, 2025
  If the diesel is overloaded in your BOMCO Water Pump, the discharge filter drum may be plugged. To resolve this, remove the filter screen and clean it.
W
Walter Hester MDAug 16, 2025
What to do if there is abnormal temperature on running friction parts like power end in my BOMCO F-1300?
- B
  Brian WilliamsAug 16, 2025
  If you observe abnormal temperature on running friction parts like the power end or crosshead of your BOMCO Water Pump, it could be due to several reasons. The oil pipe or oil port might be plugged, requiring cleaning. Alternatively, the lubricating oil may be too dirty or deteriorated, necessitating an oil change. A worn or damaged rolling bearing could also be the cause, suggesting the need for repair or replacement. Finally, ensure the lubricating oil level is correct; add more if it's too low, or reduce if it's too high.
R
raychangAug 20, 2025
How to fix low pressure and reduced discharge in BOMCO Water Pump?
- M
  Megan LarsonAug 20, 2025
  If the pressure readings are low and the discharge reduces, or there is no mud discharged from your BOMCO Water Pump, it could be due to a couple of reasons. First, the charging piping might not be sealed off, allowing air to enter the pump. Try tightening the flange bolts of the charging piping or changing the gasket. Second, the suction filter screen could be plugged. In this case, stop the pump and clean the suction filter screen.
T
Tiffany CruzAug 23, 2025
What causes abnormal knock sound on power end of BOMCO F-1300 Water Pump?
- R
  Robin ThomasAug 23, 2025
  If you hear abnormal knocking sounds on the power end, bearing, or crosshead of your BOMCO Water Pump, it could be due to several reasons. The crosshead guide might be worn out, requiring adjustment of the clearance or replacement of the worn guide. Alternatively, the bearing could be worn out, necessitating its replacement. Also, check if the guide is loose and tighten its bolts. Lastly, water hammer on the fluid end could be the cause, suggesting the need to improve the suction performance.
R
robertskinnerAug 28, 2025
What to do if the discharge pulsation dampener can’t be charged in my BOMCO F-1300?
- B
  ballardmichaelAug 28, 2025
  If the discharge pulsation dampener of your BOMCO Water Pump can’t be charged or leaks soon after charging, the charging connector might be plugged, requiring cleaning. Another possibility is that the bladder of the pulsation dampener is broken, necessitating replacement. Finally, the needle valve might not be sealed, requiring repair or replacement.
N
Nicole WilliamsAug 31, 2025
Why is there uneven discharge in my BOMCO F-1300 Water Pump?
- M
  Marcus SimonAug 31, 2025
  If you notice uneven discharge, pressure gauge fluctuations, and abnormal noise from the charging piping of your BOMCO Water Pump, it could be due to a worn or damaged piston or valve. Replace the damaged piston and inspect the valve for damage or blockage. Another possible cause is air in the pump cylinder. Check if the charging piping and valve cap are sealed off.
D
Dr. Ivan GriffinSep 4, 2025
What causes mud leakage from the alarm bore of valve cap in BOMCO Water Pump?
- J
  Jessica JonesSep 4, 2025
  If you observe mud leaking from the alarm bore of the valve cap, cylinder, and liner seal of your BOMCO Water Pump, it could be because the valve cap and cylinder cover are not tightened properly; tighten them. Alternatively, the seal ring might be damaged, requiring replacement.
W
Wayne RussellSep 8, 2025
How to troubleshoot severe knock in the liner of BOMCO Water Pump?
- B
  bryan90Sep 8, 2025
  If there is a severe knock in the liner of your BOMCO Water Pump, the piston nuts may be loose; tighten them. Alternatively, the liner cover could be loose; tighten it. Poor suction caused by water dash may also be a factor; check the reason for the improper suction.