To Next Page
M
mendezjosephSep 9, 2025
What to do if there is no water from the hot valve on my Borg & Overstrom b4?
- JJessica CookSep 9, 2025
If no water is coming from the hot valve, carry out the same checks and actions as you would for the ambient tap.
What to do if there is no water from the hot valve on my Borg & Overstrom b4?
If no water is coming from the hot valve, carry out the same checks and actions as you would for the ambient tap.
Why is my Borg & Overstrom b4 Water Dispenser tripping out the electricity supply?
If the machine is tripping out the electricity supply, it may be in a high humidity environment. If possible, reposition the machine.
What to do if the cold water is not cold because the fan is not working in my Borg & Overstrom b4 Water Dispenser?
If the cold water is not cold and the fan is not working, check and replace the fan as required.
What to do if no water comes from any valve on my Borg & Overstrom Water Dispenser?
If no water is coming from any of the valves, make sure the dispense button is being pressed firmly. If the issue persists, the controls PCB may not be working and may need to be checked and replaced.
Why is my Borg & Overstrom b4 making a bleeping noise?
If the machine is bleeping, and a level sensor is fitted, the tank may be full. Empty the level sensor tank.
What causes water to lie on the top edge of the lower door panel or the bottom of the cabinet of my Borg & Overstrom b4?
If water is lying on the top edge of the lower door panel or at the bottom of the cabinet, the drip tray waste container is likely overflowing. Empty the waste container and check that the drainpipe is not blocked.
Why does my Borg & Overstrom Water Dispenser shake when starting up?
Shaking during start-up can be normal as the compressor starts. However, ensure the machine is on a level surface; use the adjustable feet to level it if the surface is uneven. Also, check for and replace any missing fixings.
Why is the water dispensing intermittently from the sparkling water valve on my Borg & Overstrom b4 Water Dispenser?
If the water dispenses intermittently from the sparkling water valve, there may be trapped air in the pipe work; hold the button down to purge the air out. Also, ensure the button is being pressed firmly. If the issue continues, the control PCB may not be working and needs to be checked and replaced.
What causes water to lie in the bottom of my Borg & Overstrom b4?
If there is water lying in the bottom of the machine, the level sensor may not be working; check its operation and replace the batteries if needed. Alternatively, there may be a leak in the supply inlet pipe work or filter, or a leak from the machine's water pipe work fittings; locate and repair any leaks accordingly.
Why is the hot water not hot enough in my Borg & Overstrom Water Dispenser?
If the hot water is not hot enough, wait for the heating LED to stop showing, as the heating cycle may be incomplete. High hot water usage can also affect the temperature, so advise users accordingly. If the issue persists, the thermostat may not be working and may need checking and replacement. Additionally, check if the overheat function is active and reset the switch on the overheat temperature sensor if necessary.
Overview of compact water dispenser types and their availability.
Details on self-contained machines, cabinets, and power supply.
Explanation of how the cold tank is chilled via refrigeration.
How ambient water bypasses the cold tank for dispensing.
Process of chilling and carbonating water for sparkling dispense.
How hot water is heated and dispensed via a tank and solenoid.
Explanation of the instant chilling technology and its benefits.
Diagram and labels of the main parts of the water dispenser.
Details on connecting water and CO2 lines to the unit.
Steps for connecting water supply and initial operation.
Procedures for safely disconnecting and removing the machine.
Table of problems, causes, and suggested actions for no water.
Exploded view of components for the Chilled & Ambient model.
Exploded view of components for the Chilled, Ambient & Hot model.
Exploded view of components for the Chilled, Ambient & Sparkling model.
Exploded view of components for the Chilled, Hot & Sparkling model.
Exploded view of the base cabinet unit for floorstanding models.
Electrical schematic for the Chilled & Ambient configuration.
Electrical schematic for the Chilled, Ambient & Hot configuration.
Electrical schematic for the Chilled, Ambient & Sparkling configuration.
Electrical schematic for the Chilled, Hot & Sparkling configuration.
Diagram showing the water flow for Chilled & Ambient models.
Diagram showing the water flow for Chilled, Ambient & Hot models.
Diagram showing the water flow for Chilled, Ambient & Sparkling models.
Diagram showing the water flow for Chilled, Hot & Sparkling models.
Details on the high-efficiency compression system and refrigerants.
Information on the hot water tank and heating element.
Specified range for chilled water temperature.
Specified maximum temperature for hot water.
Dispensing capacity per hour for different configurations.
Electrical power consumption for various models.
Type of power connection required for the unit.
Specification for connecting the water supply line.
Specification for connecting the CO2 supply line.
Physical dimensions for countertop and base cabinet versions.
Weight specifications for different model configurations.
Information about Borg & Overström as the manufacturer.
Classification of the product.
List of models covered by the declaration.
Directives and regulations the product complies with.
List of specific standards and regulations the product meets.
Formal statement of compliance by the manufacturer.
General| Brand | Borg & Overstrom |
|---|---|
| Model | b4 |
| Category | Water Dispenser |
| Language | English |
