To Next PageTo Next PageWhat to do if my Bosch AQT 33-11 Pressure Washer motor stops?
If your Bosch Pressure Washer motor stops, first, check the fuse and replace it if it's faulty or blown. Next, verify that the mains voltage corresponds to the specifications on the model tag. Finally, the motor protector might have activated; allow the unit to cool for 15 minutes.
What to do if my Bosch AQT 33-11 Pressure Washer starts up but with restricted or no working pressure?
If your Bosch Pressure Washer starts but has restricted or no working pressure, first ensure that the water supply is connected. If it is, check the water filter for clogs and clean it if necessary. Also, inspect the nozzle for any blockages and clean it as needed.
What to do if my Bosch AQT 33-11 Pressure Washer motor starts but has no pressure?
If the motor of your Bosch Pressure Washer starts but there's no pressure, the nozzle might be partly blocked. Try cleaning the nozzle to resolve the issue.
Why does my Bosch Pressure Washer motor refuse to start?
Several factors could prevent your Bosch Pressure Washer motor from starting. Ensure the plug is properly connected. Try a different mains socket to rule out a faulty socket. Check and replace the fuse if it's faulty or blown. If you're using an extension cable, try without it, as the cable might be damaged. The motor protector might have activated; in this case, allow the unit to cool for 15 minutes. Lastly, check for freezing in the pump, water supply hose or accessory, and allow them to thaw.
Why is the pressure pulsating on my Bosch AQT 33-11?
Pulsating pressure in your Bosch Pressure Washer can be due to several reasons. It could be caused by air in the inlet water supply hose or pump; in this case, allow the pressure washer to run with open spray handle and nozzle at low pressure until regular working pressure is obtained. Another cause could be an inadequate water supply; check that the water supply corresponds to specifications, ensuring the water supply hose is at least 1/2" or 13 mm in diameter. A blocked water filter, squeezed water supply hoses, or a high pressure hose that is too long can also cause this issue. Clean the water filter, straighten out any kinked water supply hoses, and remove any high pressure extension hoses (extension hose max. 7 m).
Why does my Bosch AQT 33-11 Pressure Washer keep blowing fuses?
If your Bosch Pressure Washer keeps blowing fuses, it is likely that the fuses are incorrectly rated. Change to a mains supply higher than the pressure washer amp consumption.
Why is the pressure too low but steady on my Bosch AQT 33-11 Pressure Washer?
If the pressure is too low but steady on your Bosch Pressure Washer, the nozzle may be worn. Try changing the nozzle.
Why does my Bosch AQT 33-11 motor sound but fail to start?
If your Bosch Pressure Washer motor makes a sound but doesn't start, it could be due to an insufficient power supply. Check that the voltage of the mains power supply line is the same as that on the plate. Voltage loss due to the use of an extension cable may also be the cause; check the characteristics of the extension cable. If the appliance has not been used for a long period of time, contact your Bosch Service Centre.
Why is water leaking from my Bosch AQT 33-11 Pressure Washer?
A slight water leak from your Bosch Pressure Washer is permissible. However, if the leak is excessive, it may be due to a leaking pump, in which case you should contact the Bosch Service Centre.
Why is my Bosch AQT 33-11 Pressure Washer not taking in detergent?
If your Bosch Pressure Washer isn't taking in detergent, the detergent might be too dense. Try diluting it with water. There might also be residue or a restriction in the cleaning-agent nozzle; flush with clean water and eliminate any nozzle restrictions. If the problem persists, contact your Bosch Service Centre.
General| Form factor | Compact |
|---|---|
| Hose length | 3 m |
| Power source | Electric |
| Water filter | Yes |
| Castor wheels | No |
| Product color | Black, Green, Red |
| Detergent reservoir | - |
| Maximum pressure | 110 bar |
| Maximum flow rate | 330 l/h |
| Minimum flow rate | - l/h |
| Working pressure (max) | - bar |
| Maximum input water temperature | 40 °C |
| Power consumption (typical) | 1300 W |
Weight and Dimensions| Weight | 3800 g |
|---|
Explains symbols and general hazard warnings for safe operation.
Explanation of the automatic motor stop feature.
Diagnosing and resolving motor start problems and inconsistent water pressure.
Addressing water leaks and other operational issues.
