Why does my Bosch AQT 35-12+ Pressure Washer motor start with restricted or no working pressure?
If your Bosch Pressure Washer motor starts but provides restricted or no working pressure, first ensure that there is a water supply connected. If there is a water supply, the water filter might be clogged up. Clean the water filter. Also, the nozzle might be clogged up, so clean the nozzle.
Why is water leaking from my Bosch AQT 35-12+ Pressure Washer?
A slight water leak from your Bosch Pressure Washer is permissible. However, if the leak is excessive due to a leaking pump, contact the Bosch Service Centre.
What causes my Bosch AQT 35-12+ Pressure Washer to keep blowing fuses?
To address blown fuses in your Bosch Pressure Washer, change to a mains supply higher than the pressure washer amp consumption if the fuses are incorrectly rated.
Why does my Bosch AQT 35-12+ Pressure Washer motor sound like it's starting but won't?
If your Bosch Pressure Washer motor sounds like it's starting but fails to fully start, check these: * Make sure the voltage of the mains power supply line is the same as that on the plate. * Check the characteristics of the extension cable if you are using one, as voltage loss may occur.
Why does my Bosch Pressure Washer motor keep stopping?
If your Bosch Pressure Washer motor stops, check the following: * Replace the fuse if it's faulty or blown. * Ensure the mains voltage matches the specifications on the model tag. * Allow the motor to cool down for 15 minutes if the motor protector has activated.
Why is the pressure pulsating on my Bosch AQT 35-12+ and how to fix it?
If the pressure from your Bosch Pressure Washer is pulsating, here's what you can do: * Run the pressure washer with the spray handle open and the nozzle at low pressure until you achieve a consistent working pressure. This will remove any air in the inlet water supply. * Ensure your water supply meets the specifications, with a minimum hose diameter of 1/2" or 13 mm. * Clean the water filter. * Straighten any kinks in the water supply hoses. * If you're using a high-pressure extension hose, remove it and retry. The maximum length for an extension hose is 7 meters.
How to fix a Bosch AQT 35-12+ Pressure Washer when the motor refuses to start?
If your Bosch Pressure Washer's motor refuses to start, here are a few things to check: * Ensure the plug is properly connected. * Try a different mains socket to rule out a faulty one. * Replace the fuse if it's faulty or blown. * Remove any extension cables to see if they are the issue. * Let the motor cool down for 15 minutes in case the motor protector has activated. * If it's frozen, allow the pump, water supply hose, or accessory to thaw.
What causes water leaks from my Bosch Pressure Washer?
A slight water leak from your Bosch Pressure Washer is permissible. However, if the leak is excessive, it may indicate a leaking pump.
Why is no detergent taken in by my Bosch AQT 35-12+ Pressure Washer?
If your Bosch Pressure Washer isn't taking in detergent, make sure the adjustable nozzle isn't on a high-pressure setting. Attach the High-Pressure Foam nozzle or select the foam setting on the 3-in-1 nozzle. If the detergent is too dense, dilute it with water. If you're using a high-pressure hose extension, fit the original hose.
Why won't my Bosch Pressure Washer motor start?
Several factors could prevent your Bosch Pressure Washer motor from starting. Ensure the plug is properly connected to a working mains socket. Check the fuse and replace it if necessary. If you're using an extension cable, try without it, as the cable might be damaged. The motor protector may have activated, in which case, allow the unit to cool for 15 minutes. Lastly, check for freezing in the pump, water supply hose or accessory; allow them to thaw if frozen.
Explains general hazard alerts and symbols for safe operation.
Instructions for connecting the pressure washer to the mains power supply.
Guidelines for connecting the appliance to the water supply.
Warnings and instructions for safe use in various applications.
Safety precautions and operator responsibilities during use.
Step-by-step guide for starting the pressure washer.
Common issues and their corrective actions for the pressure washer.
General| Form factor | Upright |
|---|---|
| Cable length | 5 m |
| Power source | Electric |
| Water filter | Yes |
| Product color | Black, Green |
| Maximum flow rate | 350 l/h |
| Working pressure (max) | 120 bar |
| Maximum input water temperature | 40 °C |
| Power consumption (typical) | 1500 W |
| Surface cleaner | - |
Weight and Dimensions| Weight | 5530 g |
|---|
To Next Page
