Why does my Bosch AQT 40-13 motor sound like it's starting but won't?
If your Bosch Pressure Washer motor sounds like it's starting but fails to fully start, check these: * Make sure the voltage of the mains power supply line is the same as that on the plate. * Check the characteristics of the extension cable if you are using one, as voltage loss may occur.
Why does my Bosch AQT 40-13 motor keep stopping?
If your Bosch Pressure Washer motor stops unexpectedly, check the fuse and replace it if faulty. Ensure that the mains voltage matches the specifications on the model tag. Also, the motor protector may have activated; allow the unit to cool down for 15 minutes.
Why won't my Bosch AQT 40-13 Pressure Washer motor start?
Several factors could prevent your Bosch Pressure Washer motor from starting. Ensure the plug is properly connected to a working mains socket. Check the fuse and replace it if necessary. If you're using an extension cable, try without it, as the cable might be damaged. The motor protector may have activated, in which case, allow the unit to cool for 15 minutes. Lastly, check for freezing in the pump, water supply hose or accessory; allow them to thaw if frozen.
What to do if my Bosch AQT 40-13 motor starts but has no pressure?
If your Bosch Pressure Washer motor starts but there's restricted or no working pressure, try the following: * Connect the water supply. * Clean the water filter, as it might be clogged. * Clean the nozzle, as it might also be clogged.
What causes my Bosch AQT 40-13 to keep blowing fuses?
To address blown fuses in your Bosch Pressure Washer, change to a mains supply higher than the pressure washer amp consumption if the fuses are incorrectly rated.
Why is water leaking from my Bosch Pressure Washer?
A slight water leak from your Bosch Pressure Washer is permissible. However, if the leak is excessive due to a leaking pump, contact the Bosch Service Centre.
Why does my Bosch AQT 40-13 Pressure Washer start but have no working pressure?
If your Bosch Pressure Washer starts but has restricted or no working pressure, consider the following: * Ensure there is a water supply and connect it if necessary. * The water filter may be clogged. Clean the water filter. * The nozzle may be clogged. Clean the nozzle.
What causes low but steady pressure in my Bosch Pressure Washer?
If the pressure on your Bosch Pressure Washer is too low but steady, the issue could be: * A worn nozzle. Change the nozzle. * A worn start/stop valve. Activate the trigger five times in quick succession.
What to do if my Bosch AQT 40-13 Pressure Washer motor stops?
If your Bosch Pressure Washer motor stops, several issues could be the cause. First, check the fuse and replace it if it's faulty. Next, ensure the mains voltage corresponds to the specifications on the model tag. Lastly, the motor protector might have been activated. If so, allow the pressure washer to cool down for 15 minutes before restarting.
Why is the pressure too low, but steady, on my Bosch AQT 40-13 Pressure Washer?
If the pressure is too low but steady on your Bosch Pressure Washer, the nozzle may be worn. Consider changing the nozzle.
Provides explanations for symbols used in safety instructions and on the device.
Covers fundamental safety warnings and crucial precautions for operating the pressure washer.
Details essential electrical safety requirements and recommendations for connecting the appliance.
Specifies necessary precautions and standards for connecting the pressure washer to a water supply.
Outlines critical instructions and warnings for the safe and effective use of the pressure washer.
Details safety measures and operator responsibilities during the use of the pressure washer.
Covers safe procedures for transporting the unit and performing routine maintenance.
Information on approved accessories, spare parts, and the product's designated usage.
Presents measured sound emission and vibration values according to relevant standards.
Lists key actions for mounting and operating the unit with corresponding figure and page references.
Details the steps for starting the pressure washer and important safety warnings related to power supply.
Provides general tips and precautions for operating the pressure washer safely and effectively.
Explains the correct use of cleaning agents and the recommended cleaning method.
Guides on connecting the pressure washer to water tanks or natural sources for operation.
Lists common problems, their possible causes, and corrective actions for the pressure washer.
Details regular checks and maintenance tasks to ensure the longevity of the pressure washer.
Provides guidance on proper cleaning, draining, and storing the unit after use.
Information on contacting Bosch for spare parts, servicing, and application support.
Guidelines for protecting the environment and proper disposal of the product and its accessories.
General| Wash brush | - |
|---|---|
| Rotating nozzle | Yes |
| Form factor | Compact |
| Hose length | 6 m |
| Cable length | 5 m |
| Power source | Electric |
| Maximum flow rate | 400 l/h |
| Minimum flow rate | - l/h |
| Working pressure (max) | 130 bar |
| Working pressure (min) | - bar |
| Maximum input water temperature | 40 °C |
| Power consumption (typical) | 1900 W |
To Next Page
