Why does my Bosch AQT 37-13 motor sound like it's starting but won't?
If your Bosch Pressure Washer motor sounds like it's starting but fails to fully start, check these: * Make sure the voltage of the mains power supply line is the same as that on the plate. * Check the characteristics of the extension cable if you are using one, as voltage loss may occur.
Why does my Bosch Pressure Washer motor keep stopping?
If your Bosch Pressure Washer motor stops unexpectedly, check the fuse and replace it if faulty. Ensure that the mains voltage matches the specifications on the model tag. Also, the motor protector may have activated; allow the unit to cool down for 15 minutes.
Why won't my Bosch AQT 37-13 motor start?
Several factors could prevent your Bosch Pressure Washer motor from starting. Ensure the plug is properly connected to a working mains socket. Check the fuse and replace it if necessary. If you're using an extension cable, try without it, as the cable might be damaged. The motor protector may have activated, in which case, allow the unit to cool for 15 minutes. Lastly, check for freezing in the pump, water supply hose or accessory; allow them to thaw if frozen.
What to do if my Bosch AQT 37-13 motor starts but has no pressure?
If your Bosch Pressure Washer motor starts but there's restricted or no working pressure, try the following: * Connect the water supply. * Clean the water filter, as it might be clogged. * Clean the nozzle, as it might also be clogged.
What causes my Bosch Pressure Washer to keep blowing fuses?
To address blown fuses in your Bosch Pressure Washer, change to a mains supply higher than the pressure washer amp consumption if the fuses are incorrectly rated.
Why is water leaking from my Bosch Pressure Washer?
A slight water leak from your Bosch Pressure Washer is permissible. However, if the leak is excessive due to a leaking pump, contact the Bosch Service Centre.
What to do if my Bosch Pressure Washer motor sounds but fails to start?
If your Bosch Pressure Washer motor 'sounds' but doesn't start, it could be due to an insufficient power supply. Verify that the voltage of the mains power supply line matches what's indicated on the appliance plate. Also, check the characteristics of your extension cable, as voltage loss can occur when using one.
What causes water leaks from my Bosch Pressure Washer?
A slight water leak from your Bosch Pressure Washer is permissible. However, if the leak is excessive, it may indicate a leaking pump.
Why is my Bosch AQT 37-13 Pressure Washer pressure pulsating?
Pulsating pressure in your Bosch Pressure Washer can be caused by several factors. It could be due to air in the inlet water supply hose or pump. To resolve this, run the pressure washer with the spray handle open and the nozzle at low pressure until the pressure stabilizes. Also, check that the water supply meets the specifications, with a minimum hose diameter of 1/2" or 13 mm. Clean the water filter if it's blocked, straighten any kinks in the water supply hoses, and if using a high-pressure extension hose, remove it and retry, ensuring it doesn't exceed 7 m.
Why is no detergent taken in by my Bosch AQT 37-13?
If your Bosch Pressure Washer isn't taking in detergent, make sure the adjustable nozzle isn't on a high-pressure setting. Attach the High Pressure Foam nozzle or select the foam setting on the 3 in 1 nozzle. If the detergent is too dense, dilute it with water. If you're using a high-pressure hose extension, fit the original hose.
Explains symbols used in the manual for better understanding and safe operation.
Provides crucial safety information and instructions for operating the pressure washer.
Instructions for routine checks and upkeep of the machine.
Guidelines for cleaning, draining, and storing the pressure washer.
Information on contacting customer support for repairs and parts.
General| Max Pressure | 130 bar |
|---|---|
| Max Flow Rate | 370 L/h |
| Hose Length | 6 m |
| Cable Length | 5 m |
| Water Flow | 370 L/h |
| Frequency | 50 Hz |
To Next Page
