13Bosch Security Systems 3/23 BLCC610U
Solution 6000 User Guide
Ensure that the system (or area) is turned off.
1. Press [MENU] + [1] + [1] + [1]. The keypad will display
a list of available users that you can change their
PIN.
Ur1 John Smith
Ur2 Debbie Smith
Ur3 User 3 Name
Press OK or MENU
2. Use the [] and [] keys to select the user that you
want to change the PIN, then press [OK] to select.
Alternatively, you can enter the user number you
want to change, then press [OK].
Enter PIN for Ur2
Debbie Smith
Press OK or MENU
3. Enter the new PIN.
If an error tone sounds, try a different PIN.
4. Press [OK] to save and exit, or press [MENU] to exit
without saving.
Access > PIN Codes >
Add PIN
MENU 1-1-2
This menu allows a Master user to add a PIN to a new user.
A Master user can only program a new PIN for those users
that have been assigned to the same area(s) as the Master
user.
At factory default, each PIN is fixed to 4 digits in length.
The default PIN for User 1 (Master user) is 2580.
Enter programming mode (PIN + MENU) then,
1. Enter [MENU] + [1] + [1] + [2].
A list of users will display on the keypad.
Ur1 John Smith
Ur2 Debbie Smith
Ur3 User 3 Name
Press OK or MENU
2. Use the [] and [] keys to select the user that you
want to add a PIN, then press [OK] to select.
Alternatively, you can enter the user number you
want to add, then press [OK].
The keypad will prompt you to enter the new pin.
Enter New PIN For Ur3
User 3 Name
Press OK or MENU
3. Enter the new PIN for the user you have selected.
If an error tone sounds, try a different new PIN.
4. Press [OK] to save and exit, or press [MENU] to exit
without saving.
Access > PIN Codes >
Delete PIN
MENU 1-1-3
This menu allows a Master user the ability delete other
users PIN’s. A Master user can only delete a PIN for those
users that have been assigned to the same area(s) as the
Master user. A Master user cannot delete their own PIN.
Enter programming mode (PIN + MENU) then,
1. Make sure that the system is turned off.
2. Press [MENU] + [1] + [1] + [3].
The keypad will list all users that you can delete.
Ur1 John Smith
Ur2 Debbie Smith
Ur3 User 3 Name
Press OK or MENU
3. Use the [] and [] keys to highlight the user whose
PIN you want to delete, then press [OK] to select.
Alternatively, you can enter the user number you
want to delete, then press [OK].
Press OK To Delete PIN
For Ur2
Debbie Smith
Press OK or MENU
4. Press [OK] again to delete the PIN, or press [MENU]
to cancel.
Tokens
This section outlines how to add and delete token cards
that allow an alternate method for users to turn the system
on and off via a prox reader enabled keypad. The system
can also be configured to automatically open a door if
it has been fitted with an electric door lock. You should
discuss this feature with your installer for more details on
your particular installation.
A token is a small plastic tag card that has a unique ID. A
user can place the token card in front of a keypad that has
a built-in token reader to turn the system or specific areas
on and off.
Access > Token >
Add Token
MENU 1-2-0
This menu allows a Master user the ability to add a new
token for those users that have been assigned to the same
area(s) as the Master user.
Enter programming mode (PIN + MENU) then,
1. Enter [MENU] + [1] + [2] + [0].
A list of users will display on the keypad.
2. Use the [] and [] keys to select the user that you
want to add a token for, then press [OK] to select.
To Next Page
Loading...
