-3-
.8(433*(99-*51:,+7429-*54<*784:7(*
&3)479-*'&99*7>5&(0+7429-*54<*79441
'*+47*2&0.3, &3>&)/:892*398(-&3,.3,
&((*8847.*8478947.3,54<*794418 Such
preventive safety measures reduce the risk of
starting the power tool accidentally.
947* .)1* 54<*7944184:94+9-* 7*&(-4+
(-.1)7*3&3))4349&114<5*78438:3+&2.1.&7
<.9-9-*54<*79441479-*8*.3897:(9.43894
45*7&9* 9-* 54<*7 9441 Power tools are
dangerous in the hands of untrained users.
&.39&.354<*794418-*(0+472.8&1.,32*39
47 '.3).3, 4+ 24;.3, 5&798 '7*&0&,* 4+
5&798 &3) &3> 49-*7 (43).9.43 9-&9 2&>
&++*(99-*54<*79441C845*7&9.43+)&2&,*)
-&;* 9-* 54<*7 9441 7*5&.7*) '*+47* :8*
Many accidents are caused by poorly
maintained power tools.
**5(:99.3,944188-&75&3)(1*&3Properly
maintained cutting tools with sharp cutting
edges are less likely to bind and are easier to
control.
8* 9-* 54<*7 9441&((*8847.*8&3) 9441
'.98*9(.3&((47)&3(*<.9-9-*8*.3897:(9.438
9&0.3,.394&((4:399-*<470.3,(43).9.438
&3) 9-* <470 94'*5*7+472*)Use of the
power tool for operations different from those
intended could result in a hazardous situation.
*7;.(*
&;*>4:754<*794418*7;.(*)'>&6:&1.+.*)
7*5&.7 5*7843 :8.3, 431> .)*39.(&1
7*51&(*2*395&798 This will ensure that the
safety of the power tool is maintained.
&+*9>:1*8+47.7(:1&7&<8
*&)&118&+*9><&73.3,8&3)&11.3897:(9.438
!
WARNING
:99.3,574(*):7*8
**5 -&3)8 &<&> +742
(:99.3, &7*& &3) 9-* '1&)*
**5>4:78*(43)-&3)43&:=.1.&7>-&3)1*
4724947-4:8.3, If both hands are holding
the saw, they cannot be cut by the blade.
4 349 7*&(- :3)*73*&9- 9-* <4705.*(*
The guard cannot protect you from the blade
below the workpiece.
)/:899-*(:99.3,)*59-949-*9-.(03*884+
9-*<4705.*(*Less than a full tooth of the
blade teeth should be visible below the
workpiece.
*;*7-41) 5.*(* '*.3, (:9.3>4:7 -&3)8
47&(7488>4:71*, *(:7*9-*<4705.*(*94
&89&'1* 51&9+472 It is important to support
the work properly to minimize body exposure,
blade binding, or loss of control.
41)9-*54<*79441'>.38:1&9*),7.55.3,
8:7+&(*8 431> <-*3 5*7+472.3, &3
45*7&9.43 <-*7* 9-* (:99.3, 9441 2&>
(439&(9 -.))*3<.7.3, 47.98 4<3 (47)
Contact with a "live" wire will also make
exposed metal parts of the tool “live” and could
give the operator an electric shock.
"-*3 7.55.3, &1<&>8 :8* & 7.5 +*3(* 47
897&.,-9 *),* ,:.)* This improves the
accuracy of cut and reduces the chance of
blade binding.
1<&>8 :8* '1&)*8 <.9- (477*(9 8.?* &3)
8-&5* ).&243) ;*78:8 74:3) 4+ &7'47
-41*8Blades that do not match the mounting
hardware of the saw will run eccentrically,
causing loss of control.
*;*7 :8* )&2&,*) 47 .3(477*(9 '1&)*
<&8-*7847'419 The blade washers and bolt
were specially designed for your saw, for
optimum performance and safety of operation.
385*(9 9-* (43).9.43 &3) 6:&1.9> 4+ 9-*
<44) &3) 7*24;* &11 3&.18 +742 1:2'*7
'*+47*(:99.3,Wet lumber, green lumber or
pressure treated lumber require special
attention during cutting operation to prevent
kickback.
41) 9-* 8&< +.721> 94 57*;*39 1488 4+
(439741 Figures in this manual illustrate
typical hand support of the saw.
*5*3).3, :543 :8*9-* 8<.9(-2&>349
1&899-*1.+*4+9-*8&<+9-*8<.9(-8-4:1)
+&.1.39-*AB548.9.439-*8&<2&>349
89&79 + .9 8-4:1) +&.1 <-.1* 9-* 8&< .8
7:33.3,9-* 8&<2&>3498-:94++ If either
occurs, unplug the saw immediately and do
not use until repaired.
DANGER
!
To Next Page
Loading...
