Bosch D7412GV3 - Program Entry Guide Manual

To Next Page

Program Entry Guide

Control Panels

D9412GV3/D7412GV3 v8.11 and Higher

Get other manuals https://www.bkmanuals.com

Main Page

Table of Contents3
1.0 Introduction5
Using this Program Entry Guide5
Table 1: Differences between the D9412GV3 and5
Table 2: Literature Referenced5
Guide to Programming Options6
Local Keypad Programming7
Figure 1: D1255 Keypad Programming Menu and Page References7
Figure 2: D1260 Keypad Programming Menu and Page References8
Table 3: UL 864 Programming Requirements9
Table 4: UL 864 Programming Recommendations11
Guide to UL 864 Programming Requirements12
Panel and Area Wide Parameters12
Phone12
When the Keypad Reads Parameter Saved, Your Selection Has Been Configured.2.213
Phone Parameters14
Special Point/User Reporting15
Table 5: Modem Iiia 2 Communication Format Data - User ID Numbers15
Table 6: Modem Iiia 2 Communication Format Data - Point Numbers15
Table 7: D6000 User Ids and Zones15
Routing17
Called Party Disconnect17
Route Number Groups: Which Has the Highest Priority17
Programming Primary and Backup Destinations18
Enhanced Routing18
Programming a Duplicate Report18
Routing Destination Communication Failures18
Message Prioritization Within a Route Number18
Communication Attempts18
Table 8: SDI Path Number by Device18
Route Group Categories21
Table 9: Fire Reports21
Table 10: Burglar Reports21
Table 11: User Reports22
Table 12: Test Reports23
Table 13: Diagnostic Reports24
Table 14: Relay Reports24
Table 15: Auto-Function Reports25
Table 16: RPS Reports25
Table 17: Point Reports26
Table 18: User Change Reports26
Event Priority27
Table 19: Access Reports27
Table 20:Event Descriptions, Priorities, and Numbers27
Power Supervision29
Printer Parameters30
RPS Parameters32
Uploading and Downloading Reports32
Log Threshold Reports32
Panel Initiated Unattended RPS32
Select the Baud Rate for RPS-To-Control Panel35
Communication When Using a PSTN Connection.2.735
Miscellaneous36
Area Parameters36
Table 21: Verify Time39
Shared-Area Characteristics41
Bell Parameters41
Open/Close Options43
Arming Features47
Keypad (Command Center)50
Keypad (Command Center) Assignment50
Area Text56
Figure 3: Softkey Locations on the D1260 Keypad58
Table 22: CF### Key Strokes58
Table 23: CF### Custom Function Keystrokes58
2.10 User Interface59
2.10.1 Commands60
2.10.2 Command Authorization60
Table 24: Keypad Programming Choices60
2.10.3 Access Control Functions62
2.10.5 Configuration Authority66
Keypad Programming of the Keypad Programming67
Authority Level Selections67
L## Secure Door-Door Mode Definitions71
2.10.7 Access Control Levels75
2.10.8 SIA Duress Passcode Options77
Function List77
Relay Parameters78
2.12.1 Area Relays79
2.12.2 Panel-Wide Relays81
Passcode or Token Worksheet82
User Groups83
Passcodes83
User Group Window83
User Name83
Tokens and Cards83
Reporting and Logging84
Figure 4: User Group 122 Example84
3.0 Points87
Point Index87
Point Responses91
Applications for Point Responses 9, D, and E91
Characteristics of a Fire Point91
Bypassing a Point98
Point Assignments101
P### Relay Codes/Relays103
COMMAND 7 and COMMAND 9104
Schedules (Skeds)105
Windows105
Opening and Closing105
Window Selections105
Figure 5: Example Opening Window Timeline (Using Two Opening Windows on same Day)107
Programming for Two same Day Opening Windows (Refer to Figure 5) . 108 Programming to Link Two Days over Midnight108
Programming Example: Linking Two Closing Windows over Midnight109
Worksheet111
Opening and Closing Windows111
Normal Store Hours111
User Group Windows112
Delivery Schedule112
Monthly Auditor's Schedule112
Schedules (Skeds)114
Holiday Indexes124
Add/Change/Delete124
5.0 Auxparm125
Introduction125
RPS Requirements125
SDI Automation125
SDI RPS Parameters126
Configuration for RPS over Network127
Figure 6: COMMAND 43 Flow Chart (D1255)128
Figure 7: COMMAND 43 Flow Chart (D1265)129
Programming Path Numbers and IP Addresses for Enhanced Communications131
Figure 8: Poll Rate Timeline134
Ant-Replay Security Feature135
SDI Rps/Enhanced Communications Configuration135
Route Group Parameters136
Miscellaneous137
Cross Point Parameters139
6.0 Access Control140
Door Profile140
Cross Point Ranges Within Groups140
Effects of Programming on Custom Function Activation141
Strike Profile143
Event Profile145
7.0 SIA CP-01 Quick Reference147
Programming the Control Panels for SIA CP--01 Compliance147
Programming Prompts Directory148

Bosch D7412GV3 - Program Entry Guide Manual

Table of Contents

Other manuals for Bosch D7412GV3

Related product manuals