Bosch FLEXIDOME IP starlight 8000i Series User Manual (English)

Questions and Answers:

M
Michael ReynoldsAug 16, 2025
What to do if my Bosch Security Camera has no connection and no image transmission?
- C
  crystal27Aug 16, 2025
  If your Bosch Security Camera isn't establishing a connection or transmitting images, first ensure that the unit is configured correctly; if necessary, reset to factory default settings. Next, check all cables, plugs, contacts, and connections to rule out faulty installation. Also, verify the IP addresses and check data transmission within the LAN using ping.
J
Jeremy BurnettAug 19, 2025
Why is there moisture or condensation inside my Bosch Security Camera bubble?
- H
  Heidi YangAug 19, 2025
  If you find moisture or condensation inside the bubble of your Bosch Security Camera, or if the camera is leaking, start by re-installing the camera and ensuring it's properly closed. Make sure the rubber grommet is correctly placed, and the cabling is of the specified diameter and shape. Gently clean the air vents if they are blocked by dirt or water. If the camera has been off for a long time, turn it on and leave it on until the condensation clears.
J
Jimmy JuarezAug 22, 2025
How to troubleshoot a Bosch Security Camera that does not operate?
- S
  Shannon KelleyAug 22, 2025
  If your Bosch Security Camera unit does not operate, ensure the power supply is working properly. Check all cables, plugs, contacts, and connections for any faults. Also, if applicable, re-install the camera, ensuring that the housing closes smoothly, as improper cabling between the camera base and module can prevent proper closure.
T
tracyliuAug 26, 2025
Why is the PTRZ function not working on my Bosch Security Camera?
- B
  Brittany OliverAug 26, 2025
  If the PTRZ function of your Bosch Security Camera isn't working, begin by separating the camera module from the camera base and ensuring all cables are properly connected. If the motors have been used for a long time and have overheated, pause any lens movement until they cool down.
M
Mark LongAug 28, 2025
What to do if PTRZ does not work correctly in Bosch Security Camera?
- H
  Heather RojasAug 28, 2025
  If the PTRZ function on your Bosch Security Camera isn't working correctly, reset the PTR in the user interface to reset the pan, tilt, and roll motors. Also, reset the lens in the user interface to reset the focus and zoom of the lens.
H
hurstkristiAug 31, 2025
Why is my Bosch Security Camera not reporting an alarm?
- L
  Linda LeAug 31, 2025
  If your Bosch Security Camera is not reporting an alarm, select possible alarm sources on the Alarm sources configuration page. Also, specify the desired alarm response on the Alarm connections configuration page; if necessary, change the IP address.
P
prileySep 3, 2025
Why is there no audio transmission to remote station from my Bosch Security Camera?
- W
  William AyalaSep 3, 2025
  If you are experiencing no audio transmission to a remote station with your Bosch Security Camera, verify that all connected audio units are operating correctly. Check all cables, plugs, contacts, and connections for any faults. Also, check audio parameters on the Audio configuration and LIVE page functions pages. If the audio voice connection is already in use by another receiver, wait until the connection is free and then call the sender again.
J
jamiematthewsSep 6, 2025
What to do if Bosch Security Camera is not operational after a firmware upload?
- M
  Matthew MeyerSep 6, 2025
  If your Bosch Security Camera unit is not operational after a firmware upload, have the unit checked by Customer Service and replace it if necessary. If the problem persists, enter the IP address of the unit followed by /main.htm in your Web browser and repeat the upload.
L
Lisa OconnorSep 9, 2025
Why does my Bosch Security Camera web browser contain empty fields?
- S
  Shelby PalmerSep 9, 2025
  If your web browser contains empty fields when accessing your Bosch Security Camera, create a rule in the local computer's proxy settings to exclude local IP addresses, as an active proxy server in the network may be the cause.
A
Angela OrtegaSep 12, 2025
What to do when Bosch Security Camera reached the maximum number of connections?
- P
  Phillip RobinsonSep 12, 2025
  Wait until there is a free connection and call the transmitter again.

Bosch FLEXIDOME IP starlight 8000i Series Specifications

General

Compression	H.265, H.264, MJPEG
Vandal Resistance	IK10
Series	FLEXIDOME IP starlight 8000i
Sensor Type	CMOS
Low-light Performance	Starlight technology
Dynamic Range	120 dB
Network Protocols	IPv4, IPv6, HTTP, HTTPS, TCP, UDP, RTP, RTSP, SMTP, DNS, DDNS, DHCP, ARP, ICMP, IGMP, SNMP, FTP
Power Supply	12 VDC
Operating Temperature	-30 °C to +60 °C (-22 °F to +140 °F)
Ingress Protection	IP66
Camera Type	Dome
Lens Type	Varifocal
Frame Rate	Up to 60 fps
Network Interface	10/100 Base-T Ethernet
Power Consumption	12.9 W (PoE)