English | 13
Bosch Power Tools 1 609 92A 0MF | (9.5.14)
Technical Data
Assembly
Avoid unintentional starting of the machine. During as-
sembly and for all work on the machine, the power plug
must not be connected to the mains supply.
Delivery Scope
Before starting the operation of the machine for the first time,
check if all parts listed below have been supplied:
– Chop and mitre saw with mounted saw blade
– Tilt protector 24 with fastening set 35
(2 bolts, 2 washers, 2 square nuts)
–Dust bag 19
–Material clamp 18
– Hex key/cross-head screwdriver 22
Note: Check the power tool for possible damage.
Before further use of the machine, check that all protective
devices are fully functional. Any lightly damaged parts must
be carefully checked to ensure flawless operation of the tool.
All parts must be properly mounted and all conditions fulfilled
that ensure faultless operation.
Damaged protective devices and parts must be immediately
replaced by an authorised service centre.
Mounting Individual Components
– Carefully remove all parts provided from their packaging.
Remove all packing material from the power tool and the
accessories provided.
Mounting the Tilt Protector (see figure A)
Before using the power tool for the first time, the tilt protector
24 must be mounted.
Use the “tilt protector” fastening set 35 for mounting.
– Insert the square nuts 35 into the intended holes 34 in the
base plate.
– Place the washers 35 on the fastening bolts 35 and use
them to screw the tilt protector 24 into the inserted nuts.
Never remove the tilt protector. Without the use of the
tilt protector, the machine does not stand safely and can
tip over, especially when sawing at maximum mitre/bevel
angles.
Mounting the Extension Bars (see figure B)
Long workpieces must be underlaid or supported at their free
end.
To extend the saw table additionally, extension bars can be
mounted both to the left or right of the power tool.
– Insert the extension bars 36 on both sides of the power
tool to the stop in the drill holes 16 intended for this pur-
pose.
– Tighten the fastening bolts 37 to secure the extension
bars.
Stationary or Flexible Mounting
To ensure safe handling, the machine must be mounted
on a level and stable surface (e. g., workbench) prior to
using.
Mounting to a Working Surface (see figures C1–C2)
– Fasten the power tool with suitable screw fasteners to the
working surface. The mounting holes 14 serve for this pur-
pose.
or
– Clamp the power tool with commercially available screw
clamps by the feet to the working surface.
Mounting to a Bosch Saw Stand
With the height-adjustable legs, Bosch GTA saw stands pro-
vide firm support for the power tool on any surface. The work-
piece supports of the saw stand are used for underlaying long
workpieces.
Read all safety warnings and instructions included with
the worktable. Failure to observe safety warnings and in-
structions can lead to electrical shock, fire and/or cause
serious injuries.
Assemble the worktable properly before mounting the
power tool. Perfect assembly is important in order to pre-
vent the risk of collapsing.
– Mount the power tool in transport position on the saw
stand.
Dust/Chip Extraction
Dusts from materials such as lead-containing coatings, some
wood types, minerals and metal can be harmful to one’s
health. Touching or breathing-in the dusts can cause allergic
reactions and/or lead to respiratory infections of the user or
bystanders.
Certain dusts, such as oak or beech dust, are considered as
carcinogenic, especially in connection with wood-treatment
additives (chromate, wood preservative). Materials contain-
ing asbestos may only be worked by specialists.
– Always use dust extraction.
– Provide for good ventilation of the working place.
– It is recommended to wear a P2 filter-class respirator.
Observe the relevant regulations in your country for the mate-
rials to be worked.
Prevent dust accumulation at the workplace. Dusts can
easily ignite.
Chop and Mitre Saw GCM 10 MX
Article number
3 601 M29 0..
Rated power input
W1700
No-load speed
min
-1
4800
Weight according to
EPTA-Procedure 01/2003
kg 14.1
Protection class
/II
Permissible workpiece dimensions (maximal/minimal) see page 15.
The values given are valid for a nominal voltage [U] of 230 V. For differ-
ent voltages and models for specific countries, these values can vary.
Dimension of suitable saw blades
Saw blade diameter
mm 254
Blade body thickness
mm 1.8–2.8
Mounting hole diameter
mm 25.4
OBJ_DOKU-40624-001.fm Page 13 Friday, May 9, 2014 7:57 AM
To Next Page
Loading...
