8
Caution!
■ Do not place anything on the cooking compartment floor. Do
not cover it with aluminium foil. A build-up of heat could
damage the appliance.
The cooking compartment floor and the evaporator dish must
always be kept clear. Always place ovenware in a perforated
cooking container or on a wire rack.
■ Do not slide any accessories between the shelf positions, or
they may tip.
Optional accessories
You can obtain further accessories from specialist retailers:
Before using for the first time
In this section you will find out which steps are required before
using the appliance for the first time:
■ Setting the clock
■ Setting the water hardness range
■ Starting the appliance for the first time
■ Cleaning the accessories before use
Setting the clock
After the power has been connected, the0 symbol and ‹‹:‹‹
light up in the display. Set the clock.
1.Press the 0 button.
The time
‚ƒ:‹‹ is shown in the display.
2.Use the @ or A button to set the clock.
After a few seconds, the time which has been set is adopted.
Setting the water hardness range
Caution!
The appliance may become damaged due to the use of
unsuitable liquids.
Do not use distilled water, highly chlorinated tap water
(> 40 mg/l) or other liquids.
Only use cold, fresh tap water, softened water or uncarbonated
mineral water.
The water hardness "medium" is the default setting. Change the
value if your water is softer or harder.
You can check the water hardness with the test strips supplied
or ask your water supplier.
Notes
■ If your water is very hard, we recommend that you use
softened water.
■ If you use only softened water, you can set your appliance to
the "softened" water hardness range.
■ If you use mineral water, set the water hardness to hard.
■ If you use mineral water, you must only use non-carbonated
mineral water (see section "Filling and emptying the water
tank").
You can change the water hardness in the basic settings when
the appliance is switched off.
1.If required, turn the operating mode selector to Û to switch off
the appliance.
2.Press and hold the 0 button until ™‹ „ appears in the
display.
3.Press the 0 button repeatedly until ™† ƒ appears
("medium" water hardness).
4.Use the temperature selector to set the water hardness.
5.Press and hold the 0 button.
Your setting is saved.
Before first use
Before first use, heat the empty appliance for 20 minutes at
100 °C using
è Steam. Do not open the appliance door
during this time. The appliance is automatically calibrated (see
section: Automatic calibration).
1.Fill and insert the water tank (see section: Filling the water
tank).
Before using for the first time, moisten the seal in the tank
cover with a little water.
2.Turn the operating mode selector to è Steam.
3.Turn the temperature selector to 100 °C.
4.Press the n button.
The appliance heats up to 100 °C. The cooking time
(20 minutes) does not start to count down until the set
temperature has been reached. Do not open the appliance
door during this time.
The cooking operation ends automatically and an audible
signal sounds.
Accessories Order no.
Cooking container, solid, GN
Z, 40 mm
deep
HEZ36D453
Cooking container, perforated, GN
Z,
40 mm deep
HEZ36D453G
Cooking container, solid, GN Z, 28 mm
deep (baking tray)
HEZ36D452
Cooking container, solid, GN
Y, 40 mm
deep
HEZ36D153
Cooking container, perforated, GN
Y,
40 mm deep
HEZ36D153G
Porcelain cooking container, solid, GN
Z
HEZ36D353P
Porcelain cooking container, solid, GN
Y
HEZ36D153P
Grease filter HEZ36DF
Wire rack HEZ36DR4
Roasting set HEZ36DB4
Cleaning sponge 643 254
Descaler 311 138
Honeycomb microfibre cloth 460 770
Accessories Order no.
Water hardness Setting symbol
softened
™† ‹
1-soft
™† ‚
2-medium
™† ƒ
3-hard
™† „
4very hard
™† …
To Next Page
Loading...
