Bosch ICP-AMAX4-P2-EN - Page 8

User Code Commands
Function
(Default User Code = 2580
Default Inst. Code = 1234)
Command
Duress User Arming User Basic User Super User Master User Instal. User
Switch to Main Keypa d [Code] + [0][0 ][0] + [#] (Text KP ) √ √
Switch to Partition 01-16 [Code] + [0][ _ ][ _ ] + [# ] (Text KP) √ √
AW AY arm [Code] + [1][1 ] + [#] / [Code] + [#] / [#] (Q uick arm ) √ √ √ √ √ √
STAY arm [Code] + [1][2 ] + [#] / [Code] + [*] / [*] (Q uick arm ) √ √ √ √ √ √
Disa rm [Code] + [#] √ √ √ √ √
Disp lay Info (Fault/Tam per..) [Code] + [-] √ √
Keypad Emergency Alarm
Keypad Fire
Keypad Medical Alarm Long press [7] and [9]
Fault/Tam per Inquire [Code] + [2][1 ] + [#] √ √ √
Check All Event Log
[Code] + [2][2 ] + [#] √ √ √
Check EN Event Log
[Code] + [2][3 ] + [#] (Text KP) √ √ √
Check Dialer Event Log
[Code] + [2][4 ] + [#] (Text KP) √ √ √
Zone Bypass/Cancel
[Code] + [3][1] + [#] + [Zone No] [*] + [#] (Bypass)
√ √ √ √
[Code] + [3][1] + [#] + [Zone No] [*] + [#] (Cancel LED)
√ √ √ √
[Code] + [3][2] + [#] + [Zone No] [*] + [#](Cancel Text KP)
√ √ √ √
Bypass Inquire
[Code] + [3][3] + [#] (Text KP)
√ √ √ √
Bypass Fa ult/Tam per [Code] + [3][4 ] + [#] √ √ √ √
Siren test [Code] + [4][1 ] + [#] √ √ √
Com m u nication test [Code] + [4][2 ] + [#] √ √ √
W alk test [C ode] + [4][3] + [#] √ √ √
Change/V iew date/tim e [Code] + [5][1 ] + [#] √
Daylight S aving Tim e (+1h) [Code] + [5][2 ] + [#] √ √ √
Daylight S aving Tim e (-1h) [Code] + [5][3 ] + [#] √ √ √
Add / D elete / Change User [Code] + [5][4 ] + [#] √ √
Change Individu al Code [Code] + [5][5 ] + [#] √ √ √ √ √ √
Change D om estic Pho ne N o.1
[Code] + [5][6 ][#] + [ _ _ _ _ _ _ ][#] (LED K P ) √
Change D om estic Pho ne N o.2
[Code] + [5][6 ][#][#] + [ _ _ _ _ _ _ ][#] (LED K P ) √
Change D om estic Pho ne N o.3
[Code] + [5][6 ][#][#][#] + [ _ _ _ _ _ _ ][#] (LE D KP ) √
Change D om estic Pho ne N o.4
[Code] + [5][6 ][#][#][#][#] + [ _ _ _ _ _ _ ][#] (LED K P ) √
Change D om estic Pho ne N o.1-4 [C ode] + [5 ][6][#] + [_] + [#] + [ _ _ _ _ _ _ ][# ] (Text KP) √
Call B a ck [C ode] + [5 ][7] + [#] √
Change Language
[Code] + [5][8 ] + [#] + [ _ ] [_ ] + [#]
01= E N 0 2=D E 03=ES 04=FR
05= IT 0 6=P L 07= N L 08=SE
√ √ √
Reset tam per or fault [Code] + [6] + [#] √ √ √
Installer Access
[Code] + [7][1] + [#] (Enable)
[Code] + [7][2] + [#] (Disable)
√
System reset [Code] + [9][9 ][8][9] + [#] √ √ √
Installer program m ode [Code] + [9][5 ][8] + [#] √
Exits Progr. m ode with out save [9][5][9] + [#]
(only in Adress Progr. M ode)
√
Exits Progr. m ode with save [9][6][0] + [#]
(only in Adress P rog r. Mode)
√
Set Fa ctory D efaults [9][6][1] + [#]
(only in Adress Progr. M ode)
√
Copy control pan el data to progr. Key [9][6][2] + [#]
(only in Adress Progr. M ode)
√
Copy progr. key data to control pan el. [9][6][3] + [#]
(only in Adress Progr. M ode)
√
Disp lay FW ve rsion [9][9][9] + [#]
(on ly in Adres s Progr. Mode)
√
Long press [1] and [3] or [*] and [#]
Long press [4] and [6]
Figure 3.1: User Code Commands
8 en | Installation
AMAX panel 4000 / AMAX panel 4000
EN
2013.07 | 03 | F.01U.267.113 Quick Start Guide Bosch Sicherheitssysteme GmbH