40
Bosch Security Systems 09/07 BLCC500R FTR1.02
Copyright © 2007 E&OE
System > Power >
Fuse Options MENU 7-3-2
1 Display COMM+ Current Overload Condition Y
2 Report COMM+ Current Overload Condition Y
3 Display +12V (Accessories) Current Overload Condition Y
4 Report +12V (Accessories) Current Overload Condition Y
5 Display LAN+ Overload Condition Y
6 Report LAN+ Overload Condition Y
7 Reserved N
8 Reserved N
This location is a Bit option field. Press Keys [1] – [8] to turn ON and
OFF the required options. The option is selected or ON when the
coresponding zone indicator is on. Press [OK] To Save when finished.
System > Siren >
Tone
MENU 7-4-0
Speed
MENU 7-4-1
Volume
MENU 7-4-2
(*** System Wide Parameter ***)
1 5
Enter 0 – 15 + [OK] To Program Volume Of The Siren Volume
(0 = Disabled / 1 = Low – 15 = High)
System > Siren >
Swinger Siren
MENU 7-4-3
3
Enter 0 – 15 + [OK] To Program Number Of Times Siren Can Sound
Before Lockout. (0 = Unlimited) (*** System Wide Parameter ***)
System > Schedules >
Name
MENU 7-5-0
S c h e d u l e 1 N a m e
Use [] and [] Keys To Scroll the Cursor Left and Right. Use Keys [0]
– [9] + [] and [] To Select Characters. When finished press [OK] To
Save. Press [OFF] To Clear From The Current Cursor Position.
System > Schedules >
Time
MENU 7-5-1
Start Time Stop Time
22 : 00 12 : 00
HH MM HH MM
Using The 0 - 9 Keys Enter The Start And Stop Time As Required.
You Should Enter Two Digits For Each Option eg. 4am = 04.
Use The [] key to move to the next field.
Press [OK] to save or [MENU] to exit without saving.
Shh= Start Time Hours Snn= Start Time Minutes
Ehh= End Time Hours Enn= End Time Minutes
Schedules are programmed in 24hour time.
System > Schedules >
Day
MENU 7-5-2
Sun Mon Tue Wed Thu Fri Sat Hol
Y Y Y Y Y Y Y N
Enter 1 – 8 To Toggle Days ON/OFF. The day is active or ON when
the coresponding zone indicator is on. Indiccator 8 is used to set if the
schedule will apply on holidays. When finshed press [OK] To Save.
System > Schedules >
Function
MENU 7-5-3
0 = Disabled
0
1 = Area On/Off 3= Operate Output
2 = Area Part On/Off 4 = Timer Group
Enter 0 - 4 + [OK] To Program The Function the Schedule Will perform.
System > Schedules >
Index
MENU 7-5-4
0
(Enter Digits 0 – 15 To Program Area, Output or Access Group Number,
Then Press [OK] To Save
System > Holidays >
Name
MENU 7-6-0
H o l i d a y N a m e
Use [] and [] Keys To Scroll the Cursor Left and Right. Use Keys [0]
– [9] + [] and [] To Select Characters. When finished press [OK] To
Save. Press [OFF] To Clear From The Current Cursor Position.
System > Holidays >
Start Stop Dates
MENU 7-6-1
Start 12am Stop 12am
01 Jan 01 Jan
DD MM DD MM
Using The 0 - 9 Keys Enter The Start And Stop Date For Each Holiday As
Required. You Should Enter Two Digits For Each Option eg. June = 06.
Use The [] key to move to the next field.
Press [OK] to save or [MENU] to exit without saving.
Sdd= Start Date Snn= Start Month
Edd= End Date Enn= End Month
If the start day and month and the stop day and
month are equal then no holiday exists.
System > System Options >
General Options MENU 7-7-0
1 Display LAN Fail Y
2 Report LAN Fail Y
3 Alarm On LAN Fail N
4 Reserved N
5 Can Change Own PIN Code N
6 Monitor Default PIN Codes Y
7 PIN Always Required N
8 Display Menu Numbers Y
This location is a Bit option field. Press Keys [1] – [8] to turn ON and
OFF the required options. The option is selected or ON when the
coresponding zone indicator is on. Press [OK] To Save when finished.
(*** System Wide Parameter ***)
To Next Page
Loading...
