Bose PowerShare PS602P User Manual

pro.Bose.com
Front and Rear Panels
PowerShare PS602P
The PS602P is a 2-channel portable amplifier that allows its total 600 watts to be shared asymmetrically across both
outputs. Independently control the output level, EQ, and low-impedance / high-impedance (Low-Z/Hi-Z) settings for
each output. The PS602P supports built-in loudspeaker EQs for the FreeSpace DS 16 , DS 40, DS 100, FS3B, Panaray 402
and 802 Series IV, MA12EX, and RoomMatch Utility RMU105 and RMU108, as well as a Flat setting for FS3 systems. For
applications that require more customization, access the advanced digital loudspeaker processing features using the free
web-downloadable PowerShare Editor software.
PS602P Front Panel
Figure 4. PowerShare PS602P amplifier front panel
4~
0 04
-~ 4
)
U4~ 4)
0
_86.
'SE
<· •. . ......
0
[ o~·o
·a TO
11111111111111111111111111111111111111111111111111
SIG NAl 0 • . . · Q •. . · 1 JJ • l 22 •
UMI T 0 ~ Q
2
'
Q ~ Q ;
"' -d6 0 ""-dl 0
0
PowerS hare
PS60 2P
0
Adaptable Po wt'f Amplifier
0 POWER Switch - ON/OFF AC power.
0 POWER LED- Solid green LED indicates the unit is ON. Blinking green LED indicates the unit is in lower-power mode.
Solid amber LED indicates an over-temperature fault. A solid red LED indicates a power supply fault.
0 0 INPUT 1 & 2 SIGNAL LED - Each LED op e rat es independently.
Relative to each line-level balanced Euroblock input:
• If the SENSITIVITY DIP switch is set to 4 dBu, then the LED is green from -40 dBu to 9 dBu, with a typical input of 4
dBu . LED is amber from 9 dBu to 12 dBu. LED goes red, indicating input clipping, over 12 dBu .
•
If th e SENSITIVITY DIP s wit ch is set to 12 dBu, then th e LED is green from -40 dBu to 17 dBu, with a typical input of
12 dBu. LED is amb er from 17 dBu to 20 dBu. LED goes red, indicating input clipping, over 20 dBu.
Relative to ea ch line-level unbalanced RCA input
• If the SENSITIVITY DIP switch is set to 4 dBu, then the LED is green from -54 dBV to -5 dBV, with a typical input of
-10 dBV. LED is amber from -5 dBV to -2 dBV. LED goes red, indicating input clipping , over -2 dBV.
•
If the SENSITIVITY DIP switch is set to 12 dBu, the LED is green from -54 dBV to 3 dBV , with a typical input of -2 dBV.
LED is
amber from 3 dBV to 6 dBV. LED goes red, indicating input clipping, over 6 dBV.
Both LEOs will display so lid red if a power supply fault is detected.
G f) OUTPUT 1 & 2 LIMIT LED - Each LED operates independently.
• LED is amber when the amplifier is limiting the corresponding output due to exceeding the specified loudspeaker
Vpeak or Vrms limits.
If the sum of the amplifier outputs exceeds 600 watts, then the amplifier will limit all outputs eq ually, and all LEOs
will
show limiting simultaneously. This is because the amplifier is also measuring and limiting total output power, in
addition to individual channel output power. The amplifier is capable of delivering one-third (l/3rd) average power
continuously, 200 watts.
•
Ea ch OUTPUT LIMIT LED will d isplay solid red if there is an EHF fault on the corresponding output.
• Both LEOs will display solid red when all outputs are muted due to an amplifier fault , or if there is a power s upply
fault.
•
Both LEOs will blink red when all outputs are muted from the rear panel mute connector.
0 0 OUTPUT 1 & 2 LEVEL Control - Output attenuator for each output. Turn the controls clockwise to decrease
a
ttenuation and c ount er c lo c kwise to increase attenuation. Fully clockwi se is 0 dB a ttenu a tion, fully co unter - clockwise is
mut e. The controls are marked in dB of attenuation . There are 21 detent s with the first 12 steps s paced by 1 dB , th e next
two steps spaced by 2 dB, the following two steps spac ed by 3 dB, and the last two steps spaced by 4 dB , for a total
attenuation range of 30 dB prior to muting. The two most counterclockwise steps are mute.
In sta llation G uide
English 79

Bose PowerShare PS602P Specifications

General

Brand	Bose
Model	PowerShare PS602P
Category	Amplifier
Language	English