Bostitch SB-1842BN Original Instructions

40 pages

To Next Page

To Next Page

Page #1 background image

Loading...

Page #1 background image

SB-150SX, SB-150SXHD, SB-1664FN,

SB-2IN1, SB-1842BN, SB-1850BN,

SB-HC50FN

www.bostitch.eu

TOOL TECHNICAL DATA (ORIGINAL INSTRUCTIONS)

DONNÉES TECNIQUES (TRADUCTION DE L’ORIGINAL)

TECHNISCHE GERÄTEDATEN (ÜBERSETZUNG DES ORIGINALS)

TECHNISCHE SPECIFICATIE (VERTALING VAN ORIGINEEL)

TEKNISKE DATA (OVERSÆTTELSE AF ORIGINAL)

TEKNISET TIEDOT (KÄÄNNÖS ALKUPERÄISESTÄ)

Τεχνικά στοιχεία (ΜΕΤΑΦΡΑΣΗ ΑΠΟ ΤΟ ΠΡΩΤΟΤΥΠΟ)

DATI TECNICI (TRADUZIONE DELL’ORIGINALE)

TEKNISKE DATA (OVERSETTELSE FRA ORIGINAL)

ESPECIFICAÇÕES TÉCNICAS (TRADUÇÃO DO ORIGINAL)

ESPECIFICACIONES TÉCNICAS (TRADUCCIÓN DEL ORIGINAL)

TEKNISK DATA (ÖVERSÄTTNING AV ORIGINAL)

DANE TECHNICZNE NARZĘDZI (TŁUMACZENIE Z WERSJI ORYGINALNEJ)

TECHNICKÁ DATA NÁSTROJE (PŘEKLAD ORIGINÁLU)

TECHNICKÉ PARAMETRE (PREKLAD ORIGINÁLU)

A SZERSZÁM MŰSZAKI ADATAI (EREDETI SZÖVEG FORDÍTÁSA)

GB

FR

DE

NL

DK

FI

GR

IT

NO

PT

ES

SE

PL

CZ

SK

HU

Table of Contents

Other manuals for Bostitch SB-1842BN

Operation And Maintenance Manual38 pages

Questions and Answers:

H
Heidi MaxwellAug 13, 2025
Why is my Bostitch Power Tool lacking power and slow to cycle?
- G
  Grant HerringAug 13, 2025
  Your Bostitch Power Tool may lack power or cycle slowly if it's dry and lacks lubrication; in this case, use BOSTITCH Air Tool Lubricant. Other potential causes include a broken cylinder cap spring (replace the cap spring), cut or cracked O-rings/seals (replace them), a blocked exhaust (check the bumper, head valve spring, and muffler), a worn or leaking trigger assembly (replace it), dirt or tar buildup on the driver (disassemble the nose/driver to clean), an incorrectly seated cylinder sleeve on the bottom bumper (disassemble to correct), a dry head valve (disassemble and lubricate), or low air pressure (check the air supply equipment).
M
Mr. Christopher Mcbride Jr.Aug 21, 2025
What to do if fasteners jam in my Bostitch Power Tool?
- D
  David NolanAug 21, 2025
  If fasteners are jamming in your Bostitch Power Tool, it could be due to a worn driver channel (replace the nose and check the door), using the wrong size fasteners (use only recommended fasteners), bent fasteners (discontinue using these fasteners), loose magazine or nose screws (tighten all screws), or a broken or chipped driver (replace the driver).
J
Jeffrey BrockAug 25, 2025
Why does my Bostitch Power Tool fail to cycle?
- P
  paul08Aug 25, 2025
  If your Bostitch Power Tool fails to cycle, check the air supply equipment for any restrictions. Ensure the tool is properly lubricated with BOSTITCH Air Tool Lubricant. Other potential causes include worn head valve O-rings (replace the O-rings), a broken cylinder cap spring (replace the cylinder cap spring), or a head valve stuck in the cap (disassemble, check, and lubricate).
P
penningtonelizabethAug 28, 2025
Why is the frame or cap of my Bostitch Power Tool leaking air?
- W
  William JohnsonAug 28, 2025
  If the frame or cap of your Bostitch Power Tool is leaking air, it could be due to a damaged gasket or seal (replace the gasket or seal), a cracked or worn head valve bumper (replace the bumper), or loose cap screws (tighten and recheck).
C
Carla GomezSep 1, 2025
Why is the frame or nose of my Bostitch Power Tool leaking air?
- A
  Angela WadeSep 1, 2025
  If the frame or nose of your Bostitch Power Tool is leaking air, it might be due to loose nose screws (tighten and recheck), a cut or cracked O-ring or gasket (replace the O-ring or gasket), or a cracked or worn bumper (replace the bumper).
C
Crystal CarterSep 5, 2025
Why is the trigger valve stem of my Bostitch Power Tool leaking air?
- C
  colleenflynnSep 5, 2025
  If the trigger valve stem of your Bostitch Power Tool is leaking air, the O-rings/seals may be cut or cracked. Replace the trigger valve assembly to resolve this issue.
M
Matthew PerezSep 9, 2025
How to fix a Bostitch Power Tool with a trigger valve housing that leaks air?
- R
  Raymond HurstSep 9, 2025
  If the trigger valve housing of your Bostitch Power Tool is leaking air, it is likely due to a cut or cracked O-ring. Replace the O-ring to fix the leak.

Bostitch SB-1842BN Specifications

General

Type	Brad Nailer
Power Source	Pneumatic
Magazine Capacity	100
Operating Pressure	70-120 PSI
Air Inlet	1/4" NPT
Fastener Type	Brad Nails
Fastener Length	5/8 inch to 1-3/4 inches

Related product manuals

Bostitch SB-1850BN

Preview: Bostitch SB-150SX

Bostitch SB-150SX

Bostitch SB-100SX

Preview: Bostitch SB-125BN

Bostitch SB-125BN

Bostitch SB-1664FN

Preview: Bostitch SB-156SXHD

Bostitch SB-156SXHD

Preview: Bostitch SX1838

Bostitch SX1838

Preview: Bostitch N89C

Preview: Bostitch PN100

Preview: Bostitch BT1855

Bostitch BT1855

Preview: Bostitch MFN-201

Bostitch MFN-201