Brady BP-IP300 User Manual (English)

Other manuals for Brady BP-IP300

Operation/Configuration Manual75 pages

Specifications2 pages

Questions and Answers:

S
stacysinghAug 14, 2025
What to do if print image has smears or voids on my Brady Printer?
- L
  Laura FletcherAug 14, 2025
  If your Brady Printer prints images with smears or voids, it could be due to a few reasons. The printhead might be dirty, requiring cleaning as described on page 60. Alternatively, the temperature may be too high; try decreasing it via the software. It's also possible that the combination of labels and transfer ribbon is incorrect, in which case you should try using a different type of ribbon.
B
bennettmarkAug 17, 2025
Why does the transfer ribbon not move on my Brady BP-IP300 Printer?
- M
  mwalkerAug 17, 2025
  If your Brady Printer is transporting label media but the transfer ribbon isn't moving, there are a couple of potential causes. First, check that the transfer ribbon is correctly inserted, paying attention to the ribbon web and the label orientation. If that's not the issue, the combination of labels and transfer ribbon might be incorrect; try using a different type of ribbon.
M
Marc BarnesAug 21, 2025
How to fix vertical white lines in print image on Brady BP-IP300 Printer?
- C
  Carly JensenAug 21, 2025
  If you notice vertical white lines appearing in the print image from your Brady Printer, this could be because the printhead is dirty; refer to Cleaning the Printhead and Media Feed Rollers on page 60. Alternatively, the printhead may be defective (heat element failure), which requires service by a qualified technician.
J
Jenna GrantAug 25, 2025
Why does my Brady BP-IP300 not stop when the transfer ribbon runs out?
- C
  Charles BarkerAug 25, 2025
  If your Brady Printer continues printing even after the transfer ribbon runs out, it's likely that thermal printing is selected in the software. To resolve this, change the setting to thermal transfer printing.
J
Jacob WoodsAug 27, 2025
What to do if print image is irregular on Brady BP-IP300 Printer?
- N
  Nicholas RobinsonAug 27, 2025
  If the print image from your Brady Printer is irregular, with one side appearing lighter than the other, the printhead may be dirty. Refer to Cleaning the Printhead and Media Feed Rollers on page 60.
R
robertchanAug 30, 2025
Why is my Brady Printer printing a sequence of characters?
- J
  Jose NelsonAug 30, 2025
  If your Brady Printer is printing a sequence of characters instead of the label format, it indicates that the printer is in ASCII Dump mode. To fix this, cancel the ASCII Dump mode.
G
gkennedySep 2, 2025
Why does my Brady BP-IP300 Printer only print every second label?
- S
  Samuel ThomasSep 3, 2025
  If your Brady Printer only prints every second label, the size setting in the software is likely too large. To correct this, change the size setting in the software.
A
ashleewilsonSep 6, 2025
How to prevent transfer ribbon creases on Brady BP-IP300?
- J
  Jimmy StaffordSep 6, 2025
  If the transfer ribbon creases in your Brady Printer, it's likely because the transfer ribbon is too wide. Use a transfer ribbon slightly wider than the width of the label.
B
Benjamin Larsen PhDSep 9, 2025
Why are there horizontal white lines in print image on Brady BP-IP300 Printer?
- K
  Kimberly KirkSep 10, 2025
  If horizontal white lines appear in the print image of your Brady Printer, it's because the printer is used with backfeed > smart in the Tear-off or Peel-off mode. Always set backfeed > in the setup menu. Refer to Setup Menu on page 47.

Brady BP-IP300 Specifications

General

Printer Type	Industrial Label Printer
Print Technology	Thermal Transfer
Print Resolution	300 dpi
Connectivity	USB, Ethernet
Maximum Print Width	101.60 mm (4 in)
Cutter	Yes
Supported Media Types	Black mark labels