Briggs & Stratton 020680 - User Manual

Briggs & Stratton 020680

56 pages

To Next Page

To Next Page

Loading...

Not for

Reproduction

This pressure washer is rated in accordance to the Pressure Washer

Manufacturers Association (PWMA) standard PW101-2010 (Testing and

Rating Performance of Pressure Washers).

BRIGGS & STRATTON CORPORATION

MILWAUKEE, WISCONSIN, U.S.A.

Manual No. 80022991 Revision B

Electric Pressure Washer

OPERATOR’S MANUAL

Other manuals for Briggs & Stratton 020680

Quick Setup Guide2 pages

Questions and Answers

Y
Yvonne MoralesAug 11, 2025
Why is my Briggs & Stratton 020680 Pressure Washer pump not producing pressure?
- J
  Justin BartonAug 11, 2025
  There are several reasons why your Briggs & Stratton Pressure Washer pump might not be producing pressure. It could be due to a blocked water inlet (clear it), inadequate water supply (provide adequate flow), a kinked or leaking garden hose (straighten or replace it), a clogged water inlet screen (check and clean it), a water supply that's too hot (use cooler water), a blocked or leaking high-pressure hose (clear or replace), or an obstructed spray tip (clean it).
P
Pamela SmithAug 19, 2025
What to do if my Briggs & Stratton Pressure Washer unit fails to start when the spray gun trigger is squeezed?
- S
  stephaniebooneSep 12, 2025
  If your Briggs & Stratton Pressure Washer fails to start when you squeeze the spray gun trigger, try the following: ensure the water supply is turned on; make sure the unit is switched on using the master ON/OFF switch; verify you're using a garden hose no longer than 50 ft. (15.24 m); check the fuse box for a blown fuse and replace it, or reset the circuit breaker (do not use a fuse or circuit breaker with a higher rating); disconnect other electrical appliances and turn off lights in the circuit or operate the pressure washer on its own dedicated circuit; run pressure washer with any spray tip for 5 minutes (motor break in may be necessary).
A
Alejandra RussoAug 26, 2025
Why is my Briggs & Stratton Pressure Washer hose connections leaking?
- K
  Kari RamirezAug 26, 2025
  If you're experiencing leaks in your Briggs & Stratton Pressure Washer's hose connections, the garden hose may be loose at the water inlet (hand tighten it), the high-pressure hose connections might be loose (remove and reinstall hand tight), or the o-ring could be damaged (replace the o-ring).
A
Angela BuckleySep 2, 2025
How to fix detergent not mixing with spray in my Briggs & Stratton 020680 Pressure Washer?
- K
  Katrina FarmerSep 2, 2025
  If the detergent is not mixing with the spray in your Briggs & Stratton Pressure Washer, make sure you have the black detergent spray tip installed. Also, the inlet water supply pressure might be too high; try slowly closing the water supply valve until the chemical just starts to draw (soap suds will appear when chemical starts to draw).

Briggs & Stratton 020680 Specifications

General

Displacement	190cc
Pump Type	Axial Cam
Pump Material	Aluminum
Hose Length	25 ft
Nozzle Included	Yes
Wheel Size	10 in

Related product manuals

Preview: Briggs & Stratton 020681

Briggs & Stratton 020681

Preview: Briggs & Stratton 020498

Briggs & Stratton 020498

Preview: Briggs & Stratton 020569

Briggs & Stratton 020569

Briggs & Stratton 020238-0

Preview: Briggs & Stratton 020306-0

Briggs & Stratton 020306-0

Preview: CleanShot 020244-0

CleanShot 020244-0

Preview: SpeedClean 020239-1

SpeedClean 020239-1

SpeedClean 020239-0

Preview: SpeedClean 020212-0

SpeedClean 020212-0

Preview: SpeedClean 020227-0

SpeedClean 020227-0

SPEED CLEAN 020211-0

Speed Clean 020212-0