EasyManuals Logo

Brocade Communications Systems FastIron SX Series User Manual

Brocade Communications Systems FastIron SX Series
593 pages
To Next Page IconTo Next Page
To Next Page IconTo Next Page
To Previous Page IconTo Previous Page
To Previous Page IconTo Previous Page
Page #521 background imageLoading...
Page #521 background image
4. Congure the ethernet interface link for the owner device.
device(config)# interface ethernet 1/1/5
5. Congure the IPv6 address of the interface.
device(config-if-e1000-1/1/5)# ipv6 address 3013::2/64
6. Assign the owner device to the virtual router ID (VRID) 2.
device(conf-if-e1000-1/1/5)# ipv6 vrrp vrid 2
NOTE
You can assign a VRID number in the range of 1 through 255.
7. Designate this router as the VRRP owner device.
device(conf-if-e1000-1/1/5-vrid-1)# owner
8. Congure the VRRP version.
device(conf-if-e1000-1/1/5-vrid-2)# version 3
9. Assign an IPv6 link-local address to the VRID for use in the local network.
device(conf-if-e1000-1/1/5-vrid-2)# ipv6-address fe80::768e:f8ff:fe2a:0099
10. Assign a global IPv6 address to the VRID.
device(conf-if-e1000-1/1/5-vrid-2)# ipv6-address 3013::2
11. Enable the VRRP session.
device(conf-if-e1000-1/1/5-vrid-2)# activate
The following example
congures a VRRP owner device.
device# configure terminal
device(config)# ipv6 unicast-routing
device(config)# ipv6 router vrrp
device(config-ipv6-vrrp-router)# interface ethernet 1/1/5
device(conf-if-e1000-1/1/5)# ipv6 address 3013::2/64
device(conf-if-e1000-1/1/5)# ipv6 vrrp vrid 2
device(conf-if-e1000-1/1/5-vrid-2)# owner
device(conf-if-e1000-1/1/5-vrid-2)# version 3
device(conf-if-e1000-1/1/5-vrid-2)# ipv6-address fe80::768e:f8ff:fe2a:0099
device(conf-if-e1000-1/1/5-vrid-2)# ipv6-address 3013::2
device(conf-if-e1000-1/1/5-vrid-2)# activate
Enabling a backup VRRP device
This task is performed on any device that is designated as a backup VRRP device. For each VRRP virtual routing instance there is one
master device and all other devices are backups. For example, Router 2 in Figure 36 on page 519 is assigned as a backup device.
Repeat this task for all devices that are to be designated as backup devices.
1. On the device designated as a backup VRRP device, from privileged EXEC mode, enter
conguration mode by issuing the
congure terminal command.
device# configure terminal
Basic VRRP parameter conguration
FastIron Ethernet Switch Layer 3 Routing
53-1003627-04 521

Table of Contents

Other manuals for Brocade Communications Systems FastIron SX Series

Questions and Answers:

Question and Answer IconNeed help?

Do you have a question about the Brocade Communications Systems FastIron SX Series and is the answer not in the manual?

Brocade Communications Systems FastIron SX Series Specifications

General IconGeneral
BrandBrocade Communications Systems
ModelFastIron SX Series
CategorySwitch
LanguageEnglish

Related product manuals