Why does my Brother All in One Printer say 'Cover is Open'?
If your Brother All in One Printer shows 'Cover is Open', it means the front cover, ADF cover, or fuser cover isn't completely closed, or paper was jammed when you turned on the power. Make sure to completely close the indicated cover. If paper was jammed, remove it, then close the fuser cover and press Start.
What to do if my Brother MFC-8810DW Printer says 'Connection Fail'?
If you see a 'Connection Fail' message on your Brother printer, it means the printer and your mobile device aren't communicating properly during setup. To fix this: * Move your mobile device closer to the Brother printer. * Ensure there are no obstructions between the printer and the mobile device. * If using the PIN Method of WPS, verify that you've entered the correct PIN code.
How to fix Brother Printer when wireless network setup configuration cannot be completed?
If you cannot complete the wireless network setup configuration on your Brother Printer, here are a few things to try: First, turn your wireless router off and then back on, and try configuring the wireless settings again. Second, double-check and make sure you're choosing the correct security settings. You might find these settings on your WLAN access point/router or by contacting your Internet provider or network administrator. Third, confirm that the MAC address of your Brother machine is allowed in the filter; you can usually find this on the printer's control panel. Also, make sure you're typing the correct SSID name or Network Key manually. Lastly, try using the Network Connection Repair Tool.
What should I do if my Brother All in One Printer says 'No Toner'?
If your Brother All in One Printer displays 'No Toner', remove the drum unit and toner cartridge assembly, remove the toner cartridge from the drum unit, and re-install the toner cartridge back into the drum unit again. Re-install the drum unit and toner cartridge assembly back in the machine. This issue occurs when the toner cartridge or the drum unit and toner cartridge assembly is not installed correctly.
How to fix 'No Paper' error on Brother All in One Printer?
If your Brother All in One Printer displays 'No Paper', refill paper in the tray shown on the LCD or in all trays. Ensure the paper guides are set to the correct size. Alternatively, remove the paper and load it again, making sure the guides are correctly sized. This occurs when the machine is out of paper or the paper isn't loaded correctly.
What does 'Disconnected' mean on my Brother All in One Printer when faxing?
If your Brother All in One Printer displays 'Disconnected', try sending or receiving again. This message means the other person or their fax machine stopped the call.
How to fix Brother Software 'Authenticate Err Sending Error'?
If you receive an 'Authenticate Err Sending Error' with your Brother Software, it could be due to a wrong username or password. Confirm your username and password for the CIFS server. If the username is part of the domain, ensure you include the domain name with the username, for example, user@domain or domain\user.
How to fix Brother Software when I cannot communicate with my Brother machine using SSL?
To communicate with your Brother machine using SSL, ensure you obtain a valid certificate and install it on both your machine and computer. Also, verify that the port setting of your machine is correct. You can confirm your machine’s port setting on the Web Based Management screen by clicking Network, Protocol, and then HTTP Server Settings.
How to fix 'Duplex Disabled' on Brother All in One Printer?
If your Brother All in One Printer displays 'Duplex Disabled', close the back cover of the machine. This message appears when the back of the machine is not closed completely.
How to activate wireless setting on Brother All in One Printer?
To activate the wireless setting on your Brother All in One Printer, turn the wireless setting to ON. If a LAN cable is connected, disconnect it and then turn the wireless setting on. On your printer, press Menu, then 7 (Network), then 2 (WLAN), then 2 (Setup Wizard). When 'WLAN Enable ?' is displayed, choose 'On' and press OK. This will start the wireless setup wizard.
General| Print Technology | Laser |
|---|---|
| Functions | Print, Copy, Scan, Fax |
| Print Resolution | Up to 1200 x 1200 dpi |
| Automatic Duplex Printing | Yes |
| ADF Capacity | 50 sheets |
| Monthly Duty Cycle | Up to 50, 000 pages |
| Memory | 128 MB |
| Fax Speed | 33.6 kbps |
| Processor | 400 MHz |
| Connectivity | USB, Ethernet, Wi-Fi Direct |
| Scanning Resolution | Up to 19200 x 19200 dpi (Interpolated) |
| Mobile Printing | Brother iPrint&Scan, AirPrint, Google Cloud Print |
| Maximum Paper Size | Legal (8.5" x 14") |
| Print Speed | Up to 40 ppm |
To Next Page
