How to fix 'Cartridge Error Put the Toner Cartridge back in' on Brother All in One Printer?
If your Brother All in One Printer displays 'Cartridge Error Put the Toner Cartridge back in', it means the toner cartridge isn't installed correctly. Remove the drum unit and toner cartridge assembly, take out the toner cartridge, and put it back into the drum unit again. Then, put the drum unit and toner cartridge assembly back in the machine.
Why does my Brother All in One Printer say 'Cover is Open'?
If your Brother All in One Printer shows 'Cover is Open', it means the front cover, ADF cover, or fuser cover isn't completely closed, or paper was jammed when you turned on the power. Make sure to completely close the indicated cover. If paper was jammed, remove it, then close the fuser cover and press Start.
How to activate wireless setting on Brother All in One Printer?
To activate the wireless setting on your Brother All in One Printer, turn the wireless setting to ON. If a LAN cable is connected, disconnect it and then turn the wireless setting on. On your printer, press Menu, then 7 (Network), then 2 (WLAN), then 2 (Setup Wizard). When 'WLAN Enable ?' is displayed, choose 'On' and press OK. This will start the wireless setup wizard.
Why does my Brother All in One Printer say 'Cooling Down Wait for a while'?
If your Brother All in One Printer displays 'Cooling Down Wait for a while', ensure the fan is spinning and the exhaust outlet isn't blocked. Remove any obstacles around the outlet. If the fan isn't spinning, disconnect the machine from power for several minutes, then reconnect it. This message appears when the drum unit or toner cartridge is too hot.
What does 'Toner Low' mean on my Brother All in One Printer?
If your Brother All in One Printer displays 'Toner Low', it means the toner cartridge is near the end of its life. Order a new toner cartridge now, so you have a replacement when the LCD shows 'Replace Toner'.
What does 'Disconnected' mean on my Brother All in One Printer when faxing?
If your Brother All in One Printer displays 'Disconnected', try sending or receiving again. This message means the other person or their fax machine stopped the call.
What to do if my Brother MFC-8810DW Printer 'Cannot Connect' because a device is already connected?
If your Brother printer displays 'Cannot Connect A device is already connected', it means another mobile device is already connected to the Wi-Fi Direct network when the Brother machine is the G/O (Group Owner). Wait for the current connection between your Brother machine and the other mobile device to shut down, and then try configuring the Wi-Fi Direct settings again.
Why does my Brother MFC-8810DW Printer show a 'Connection Error'?
A 'Connection Error' on your Brother printer indicates that other devices are attempting to connect to the Wi-Fi Direct network simultaneously. To resolve this, ensure no other devices are trying to connect to the Wi-Fi Direct network, and then attempt to configure the Wi-Fi Direct settings again.
What to do if my Brother MFC-8810DW shows a 'No Device' error?
If your Brother printer displays a 'No Device' error, it means the printer can't find your mobile device. Here’s what to do: * Ensure both your printer and mobile device are in Wi-Fi Direct mode. * Move the mobile device closer to the Brother printer. * Remove any obstructions between the devices. * If manually configuring Wi-Fi Direct, verify the password is correct. * If your mobile device requires IP address configuration, ensure it's set to DHCP.
How to fix Brother Printer when wireless network setup configuration cannot be completed?
If you cannot complete the wireless network setup configuration on your Brother Printer, here are a few things to try: First, turn your wireless router off and then back on, and try configuring the wireless settings again. Second, double-check and make sure you're choosing the correct security settings. You might find these settings on your WLAN access point/router or by contacting your Internet provider or network administrator. Third, confirm that the MAC address of your Brother machine is allowed in the filter; you can usually find this on the printer's control panel. Also, make sure you're typing the correct SSID name or Network Key manually. Lastly, try using the Network Connection Repair Tool.
General| Print Technology | Laser |
|---|---|
| Functions | Print, Copy, Scan, Fax |
| Print Resolution | Up to 1200 x 1200 dpi |
| Automatic Duplex Printing | Yes |
| ADF Capacity | 50 sheets |
| Monthly Duty Cycle | Up to 50, 000 pages |
| Memory | 128 MB |
| Fax Speed | 33.6 kbps |
| Processor | 400 MHz |
| Connectivity | USB, Ethernet, Wi-Fi Direct |
| Scanning Resolution | Up to 19200 x 19200 dpi (Interpolated) |
| Mobile Printing | Brother iPrint&Scan, AirPrint, Google Cloud Print |
| Maximum Paper Size | Legal (8.5" x 14") |
| Print Speed | Up to 40 ppm |
To Next Page
