1. Print from the Label Printer
Safety Precautions
Be sure to read this section before using the product. It contains important safety instructions.
We recommend that you keep this document nearby for future reference.
• For servicing, adjustments, or repairs, contact Brother customer service or your local Brother dealer.
• If the product operates abnormally or any error occurs, or if any cable is damaged, turn the product off,
disconnect all cables, and contact Brother customer service or your local Brother dealer.
• We assume no responsibility for damages arising from earthquakes, re, other disasters, actions of third
parties, the user’s intentional or negligent operation, misuse, or operation under other special conditions.
• We assume no responsibility for damage (such as losses, loss of business prot, lost prots, business
disruptions, or a lost means of communication) that may result from the use of, or inability to use, the
product.
• We assume no responsibility for damages that may result from incorrect operation of the product by
connecting incompatible equipment or using incompatible software.
• We assume no responsibility for any damages or lost prot arising from the use of labels created with this
product, the disappearance or change of data due to failure, repair, or consumables and we do not accept
any claim from a third party.
• Brother reserves the right to make changes without notice in the specications and materials contained
herein. Furthermore, Brother shall not be responsible for any damages (including consequential) caused by
reliance on the materials presented, including but not limited to typographical and other errors relating to
the publications.
• For more information about the available software, see the User’s Guide on the Brother support website at
support.brother.com.
• The latest version of your product documentation is available on the Brother support website at
support.brother.com.
• The available models, accessories, and supplies may vary depending on the country or region.
• This product is approved for use in the country or region of purchase only.
WARNING
Failure to observe instructions and warnings could result in death or serious injuries.
• DO NOT operate, charge, or store the Label Printer, AC Adapter, USB Cable, and Alkaline Batteries in the
following locations (otherwise a re, electrical shock, smoke, or damage may occur):
- Near water, such as in a bathroom or near a water heater, or in an extremely humid or cold location.*
- In a location where it is exposed to rain or moisture.
- In an extremely dusty location.
- In an extremely hot location, such as near open ames, heaters, or in direct sunlight.
- In a closed car in direct sunlight.
- In a location where condensation may form.
- At a high altitude.
- During a thunderstorm.
• DO NOT use the Label Printer with a foreign object in it. If water, a metal object, or any other foreign object
enters the Label Printer, disconnect the AC Adapter and remove the batteries (if installed), and then contact
your local Brother dealer for repairs.
• If foreign objects are inserted into the Label Printer or its slots, connectors, ports, or Battery Compartment,
stop using the Label Printer, turn the power off, and then disconnect each cable or remove the batteries
(if installed).
• Stop using the Label Printer if there are noticeable abnormalities such as smell, heat, noise, deformities,
or discolouration.
• DO NOT use a damaged AC Adapter.
To avoid damaging the Label Printer, AC Adapter, USB Cable, or Alkaline Batteries, DO NOT:
- Place heavy objects on them.
- Dissamble or modify them.
- Drop or hit them.
- Allow them to get wet, for example, by handling them with wet hands or spilling liquids on them.
• DO NOT allow babies and children to play with the plastic bag that contained the Label Printer.
Dispose of the bag or keep it away from babies and children. There is a risk of suffocation.
* For more information, see the “Specications” section in your model’s User’s Guide.
• DO NOT forcibly bend or pull the USB Cable or AC Adapter.
• DO NOT touch the AC Adapter or plug with wet hands, otherwise an electrical shock may occur.
• Use only the specied AC Adapter.
• Use only the AC Adapter and USB Cable included with your Label Printer. Failure to do so may result in an
injury to yourself or others, or damage to the Label Printer, or other property. Brother does not assume any
responsibility for any accident or damage resulting from not using the specied AC Adapter and USB Cable.
• DO NOT connect the included AC Adapter and USB Cable to other products.
• Use the AC Adapter with standard electrical sockets (AC 100 V - 240 V 50/60 Hz).
• Insert the plug rmly into the electrical socket.
• DO NOT use the batteries if they are damaged or leaking.
• Keep batteries away from infants. If batteries are ingested, contact emergency services immediately.
• DO NOT use sharp objects, such as tweezers or a metallic pen, to remove or replace batteries.
• If liquid (electrolyte) from the batteries gets into the eyes, wash them immediately with clean water. Contact
emergency services immediately.
• DO NOT solder connections to the batteries.
• DO NOT use the batteries with the polarity (+) (-) reversed.
• DO NOT connect the + and - terminals with metal objects such as wire.
• DO NOT incinerate the batteries or dispose of them with household waste.
• Keep ngers and other body parts away from the Cutter unit.
• DO NOT touch the Cutter unit’s blade or insert your ngers inside the
Tape Exit Slot, otherwise ngers and other body parts may be injured.
• DO NOT touch any metal parts near the Print Head. The Print Head
becomes very hot during and immediately after use. DO NOT touch it
directly with your hands.
CAUTION
Failure to observe instructions and warnings could result in minor or moderate injuries.
Label Printer, USB Cable, AC Adapter, Alkaline Batteries
• Use only the specied AA alkaline batteries (LR6).
• DO NOT use combinations of old and new batteries or combinations of different types, charging levels,
manufacturers, or models.
• DO NOT drop the Label Printer when removing it from the box or relocating it, otherwise you may get
injured.
• Be careful when closing the Tape Cassette Compartment Cover. There is a risk of injury if your nger gets
pinched between the upper and lower parts of the cover.
• When you are not using the Label Printer, store it out of the reach of children. In addition, do not allow
children to put the Label Printer parts or labels in their mouths. If any object has been swallowed, seek
medical attention immediately.
• DO NOT leave the Label Printer or any tape within the reach of babies and children.
• Store the Label Printer on a at, level, and stable surface.
• Remove the batteries and disconnect the AC Adapter if you do not intend to use the printer for an extended
period of time.
• DO NOT press on the Liquid Crystal Display (LCD).
• When disconnecting the AC Adapter from the electrical socket, always hold the AC Adapter.
• DO NOT overload an electrical circuit with the AC Adapter.
• DO NOT open the Tape Cassette Compartment Cover when operating the Cutter unit.
• DO NOT apply excessive pressure to the Cutter unit.
Product Safety Guide
Regulation
Declaration of Conformity (Europe only)
We, Brother Industries, Ltd.
15-1, Naeshiro-cho, Mizuho-ku, Nagoya 467-8561 Japan
declare that this machine is in conformity with the relevant EU harmonization legislation
(Europe only) and UK legislation (Great Britain only).
The Declaration of Conformity (DoC) can be downloaded from our website.
Visit support.brother.com/manuals.
CAUTION
RISK OF EXPLOSION IF BATTERIES ARE REPLACED WITH AN INCORRECT TYPE.
DISPOSE OF USED BATTERIES ACCORDING TO THE INSTRUCTIONS.
Information for compliance with Commission Regulation 801/2013
PT-D410
Power consumption* 0.6W
* All network ports activated and connected
2. Install Batteries or Connect the AC Adapter
Remove the protective material (rst use only) before using the Label Printer.
Batteries
AC Adapter
• When using the AC Adapter (AD-E001A):
- Insert the Adapter cord connector into the AC Adapter
Jack on the side of the printer.
- Insert the plug into the nearest standard electrical
socket. For memory backup, we recommend using AA
alkaline batteries (LR6) together with the AC Adapter.
• To safeguard and back up the Label Printer’s memory,
when the AC Adapter is unplugged, keep AA alkaline
batteries (LR6) installed in the Label Printer.
• When power is disconnected for more than two minutes,
all text and format settings will be cleared. Any text les
stored in the memory will also be cleared.
• Remove the batteries if you do not intend to use the
Label Printer for an extended period of time.
• Dispose of the batteries at an appropriate collection point,
not in the general waste stream. In addition, be sure to
observe all applicable federal, state, and local regulations.
• When storing or discarding the batteries, wrap them
(for example with cellophane tape), to prevent them from
short-circuiting.
(Battery insulation example)
1. Cellophane tape
2. Alkaline battery
1
2
2. Print from Your Computer
on-screen instructions.
Mac. You do not need to download and install any drivers.
Label creation software for computers. This application comes with
frames, imported images, barcodes, and more.
the included USB Cable.
• This Label Printer does not support Wi-Fi connections.
3. Application Installation
and troubleshooting tips.
To Next Page
Loading...
Need help?
General
