What to do if Brother PJ-722 Printer ejects a partially printed page?
If the Brother printer ejects a partially printed page, and the DATA indicator remains lit or flashing in green, use the correct paper size setting.
What to do if my Brother Printer is not detected via Wi-Fi?
If your Brother printer (PJ-773 only) is not detected when establishing a Wi-Fi connection, check that the (Wi-Fi) indicator is lit in blue. If the (Wi-Fi) indicator is flashing or turned off, the Wi-Fi connection is not established. You can also check the Wi-Fi settings, print the printer settings, or specify the correct Wi-Fi settings in the Printer Setting Tool, consulting with the network administrator if needed.
How to reset Brother PJ-722 Printer to factory settings?
To reset your Brother printer and delete the data transferred from a computer or mobile device, follow this procedure: 1. Confirm that the printer is turned off. 2. While holding down the (Feed) button, press the (Power) button three times, and then release the (Feed) button. The POWER indicator starts flashing in orange. 3. Press the (Feed) button three times to reset the printer's communication and device settings to their factory settings and delete all the data transferred to the printer.
Why is my Brother PJ-722 Printer print quality poor?
If the print quality of your Brother printer is poor, and the printed image is too light or too dark, adjust the print density setting in the printer driver’s dialog box, or in the Printer Setting Tool. Also, ensure that you are using genuine Brother thermal paper.
How to confirm IP address and Subnet Mask for Brother Printer?
To confirm the IP address and the Subnet Mask for your Brother printer, confirm the IP address and the Subnet Mask. Verify that both the IP addresses and Subnet Masks of your computer and your printer are correct and located on the same network. Confirm your IP address, Subnet Mask and other network settings using the Printer Setting Tool.
What to do if my Brother PJ-722 is not detected via Bluetooth?
If your Brother printer (PJ-762/PJ-763/PJ-763MFi only) is not detected when establishing a Bluetooth connection, check that the (Bluetooth) indicator is lit in blue. If the (Bluetooth) indicator is flashing or turned off, the Bluetooth connection is not established. Check the Bluetooth settings, print the printer settings, and specify the correct Bluetooth settings in the Printer Setting Tool.
What to do if I am using security software with Brother PJ-722 Printer?
If you are using security software with your Brother printer, confirm your settings in the installation dialog box. Allow access when the security software alert message appears during the printer installation.
Why does Brother PJ-722 paper not feed even though the motor is running?
If the paper does not feed in your Brother printer even though the motor is running, make sure the release cover is completely closed and that you use genuine Brother thermal paper. If you still have problems, the printer may be damaged. Contact your Brother dealer or Brother Customer Service for assistance.
Why is my Brother PJ-722 Printer side margins incorrect?
If the side margins are incorrect on your Brother printer, make sure the correct margins have been set in the Printer Setting Tool or your application. Adjust the left margin as needed. Also, make sure the application, the printer, and the printer driver have been set to match the paper size of the paper that is loaded in the printer. If the application or printer driver has been set to a different paper width, the image will not be printed in the proper horizontal position, so adjust the settings as needed.
Why is my Brother PJ-722 Wi-Fi connection taking too long?
If the Wi-Fi connection is taking too long to connect on your Brother printer (PJ-773 only), note that from initialization to completing the connection takes time, so it may take a minute or more to establish the Wi-Fi connection. This differs depending on the device and environment, so check with the device manufacturer.
General| Print Technology | Direct Thermal |
|---|---|
| Print Speed | Up to 8 ppm |
| Interface | USB |
| Power Source | AC adapter |
| Dimensions | 255 mm x 55 mm x 30 mm |
| Weight | 480 g |
| Paper Size | A4, Letter |
| Media Type | Roll paper, Fanfold paper |
To Next Page
