Brother PJ-723 User Manual (English)

Other manuals for Brother PJ-723

Online User's Guide165 pages

User Guide7 pages

Command Reference62 pages

Questions and Answers:

R
Robert WoodAug 23, 2025
What to do if the Brother PJ-723 DATA indicator remains green but doesn't print?
- T
  Todd MartinezAug 23, 2025
  If the DATA indicator is lit but your Brother printer isn't printing, it could be due to several reasons. First, the printer might still be processing received data, so wait until it finishes. Ensure paper is loaded; if it is, try removing and reloading it. You can also try turning the printer off and on again. If sending simple ASCII text data, the printer may be waiting for a CR/LF command at the end of lines or a form feed command at the end of the last line. Print another page, or press the (Feed) button. Finally, the printer may have started in mass storage mode; in that case, turn it off and on again.
C
Cassandra FisherSep 1, 2025
How to confirm IP address and Subnet Mask for Brother PJ-723?
- T
  Tonya PetersSep 1, 2025
  To confirm the IP address and the Subnet Mask for your Brother printer, confirm the IP address and the Subnet Mask. Verify that both the IP addresses and Subnet Masks of your computer and your printer are correct and located on the same network. Confirm your IP address, Subnet Mask and other network settings using the Printer Setting Tool.
J
Joseph BarreraAug 30, 2025
Why is my Brother PJ-723 Printer print quality poor?
- C
  Craig SmithAug 30, 2025
  If the print quality of your Brother printer is poor, and the printed image is too light or too dark, adjust the print density setting in the printer driver’s dialog box, or in the Printer Setting Tool. Also, ensure that you are using genuine Brother thermal paper.
L
Lee CooperAug 29, 2025
Why is the image compressed and stretched on my Brother Printer?
- J
  Joshua TaylorAug 29, 2025
  If the image is compressed and stretched, make sure the release cover was not left open during printing and is now completely closed. Ensure you are using genuine Brother thermal paper, and that the paper is not wrinkled before loading.
H
heather44Aug 28, 2025
How to reset Brother Printer to factory settings?
- K
  Kevin MartinAug 28, 2025
  To reset your Brother printer and delete the data transferred from a computer or mobile device, follow this procedure: 1. Confirm that the printer is turned off. 2. While holding down the (Feed) button, press the (Power) button three times, and then release the (Feed) button. The POWER indicator starts flashing in orange. 3. Press the (Feed) button three times to reset the printer's communication and device settings to their factory settings and delete all the data transferred to the printer.
G
Gerald MillerAug 27, 2025
What to do if my Brother PJ-723 Printer is not detected via Wi-Fi?
- E
  Eric GillAug 28, 2025
  If your Brother printer (PJ-773 only) is not detected when establishing a Wi-Fi connection, check that the (Wi-Fi) indicator is lit in blue. If the (Wi-Fi) indicator is flashing or turned off, the Wi-Fi connection is not established. You can also check the Wi-Fi settings, print the printer settings, or specify the correct Wi-Fi settings in the Printer Setting Tool, consulting with the network administrator if needed.
B
Brenda ClarkAug 27, 2025
What to do if Brother Printer prints blank pages?
- J
  Jennifer MurphyAug 27, 2025
  If your Brother printer feeds paper but nothing appears on the paper, ensure you are using thermal paper. Also, the print surface must face the back when looking from the front of the printer. You can also check the print density setting using the Printer Setting Tool.
W
wilkinsstefanieAug 26, 2025
What to do if the Brother PJ-723 paper feeds through but nothing prints?
- T
  Tanya TaylorAug 26, 2025
  If paper feeds through your Brother printer but nothing appears on it, make sure you are using thermal paper and that the print surface faces the back when looking from the front of the printer.
C
cameronbrockAug 25, 2025
What to do if my Brother PJ-723 ejects a partially printed page?
- M
  mullinsjohnAug 26, 2025
  If your Brother printer ejects a partially printed page, ensure you are using the correct paper size setting.
A
Amanda StantonAug 25, 2025
Why is my Brother Printer not feeding paper, even though the motor is running?
- V
  vfriedmanAug 25, 2025
  If your Brother printer's motor is running, but the paper isn't feeding, make sure the release cover is completely closed. Also, ensure you are using genuine Brother thermal paper, as other types may not feed correctly. If problems persist, the printer may be damaged.

Brother PJ-723 Specifications

General

Print Technology	Direct Thermal
Resolution	300 dpi
Maximum Print Speed	8 pages per minute
Interface	USB
Dimensions	255 mm x 55 mm x 30 mm
Weight	0.48 kg
Power Source	AC Adapter
Paper Size	A4