T
Tammie BonillaSep 7, 2025
What does 'Err 2' mean on my Brother S-7200A Sewing Machine?
- MMelanie JacksonSep 7, 2025
If 'Err 2' appears, connector CN7 or CN8 inside the control box might be disconnected. Insert the connector securely.
To Next PageTo Next PageWhat does 'Err 2' mean on my Brother S-7200A Sewing Machine?
If 'Err 2' appears, connector CN7 or CN8 inside the control box might be disconnected. Insert the connector securely.
What does “GREASEUP” flashing on the operation panel of my Brother Sewing Machine mean?
Apply grease.
What to do if my Brother S-7200A Sewing Machine does not operate at high speed?
If the machine does not operate at high speed, the sewing speed setting or backtack speed setting may be incorrect. Use the sewing speed control keys to set the high speed.
What to do if my Brother S-7200A is producing correct thread trimming, but the upper thread or lower thread is not being trimmed?
If the upper thread or lower thread is not being trimmed, ensure the needle is correctly installed. If it is incorrect, install the needle correctly. Also, the fixed knife or movable knife might be blunt, so replace them.
What to do if my Brother S-7200A Sewing Machine is producing correct thread trimming, but the upper and lower threads are not being trimmed?
If the upper and lower threads are not being trimmed, the fixed knife or movable knife may be damaged or worn. Replace the fixed knife or the movable knife.
What to do if skipped stitches occur while sewing with my Brother S-7200A?
If skipped stitches occur while sewing, it could be due to several reasons. Check if the needle tip is bent and replace the needle if necessary. Ensure the needle is properly installed and the machine is correctly threaded. Adjust the presser foot pressure if it's too weak. If the needle is too thin, replace it with a thicker one. Also, adjust the height of the presser foot if it's too high and adjust the tension of the thread take-up spring.
What causes loops to appear in the seam of my Brother S-7200A and how to fix it?
Loops in the seam can appear if the thread path isn't smooth enough; polish it with a fine grain file or sandpaper. Also, check if the bobbin isn't turning smoothly; pull out the lower thread to check for slackness, or replace the bobbin or bobbin case.
How to fix skipped stitches at sewing start on my Brother S-7200A?
To fix skipped stitches at the sewing start, reduce the tension of the thread take-up spring and lower its position. Adjust the pretension if the trailing lengths of the upper threads are too short after trimming. Sharpen the fixed knives or replace them if the threads aren't being trimmed cleanly. Use a needle with a count one lower if the current needle is too wide. Replace the anti-spin spring in the bobbin case if the bobbin is spinning loosely. Finally, use the slow start feature if the sewing speed is too fast.
What to do if my Brother Sewing Machine is making an uneven seam?
An uneven seam can occur if the presser foot pressure is too weak, so adjust the presser foot pressure. It could also be that the feed dog is too low, in which case you should adjust the feed dog height. Finally, check if the bobbin is scratched; if it is damaged, smooth it or replace it.
What to do if the oil gauge is not visible in oil gauge window of my Brother Sewing Machine?
If the oil gauge is not visible in the oil gauge window of your Brother Sewing Machine, the oil tank may be empty. Fill the oil tank with oil.
General| Type | Industrial Sewing Machine |
|---|---|
| Model | S-7200A |
| Stitch Type | Lockstitch |
| Max. Sewing Speed | 5, 000 stitches per minute |
| Max Stitch Length | 4.5 mm |
| Needle Bar Stroke | 30.7 mm |
| Needle Type | DB×1 (#11) #9~#18 |
| Motor | Direct Drive Motor |
| Foot Lift | By hand: 5.5mm, By knee: 13mm |
| Lubrication | Automatic oiling system |
