Burkert 8045 Manual

8045
p. 1/6www.burkert.com
Technical data
General data
Compatibility
with fittings S020
(see corresponding data sheet)
Materials
Housing, cover, nut
PVDF sensor version
St.St. sensor version
Front panel foil
Protection lid
Screws / Seal / Cable glands
Wetted parts materials
Sensor armature
Electrodes
Gaskets
Earth ring
(PVDF sensor version)
Electrode holder (St.St. sensor version)
PC (glass fibre reinforced for housing)
PPA (glass fibre reinforced)
Polyester
PSU
Stainless steel / EPDM / PA
PVDF or Stainless steel 1.4404/316L
Stainless steel 1.4404/316L or Alloy C22
FKM
(FDA agreements)
Stainless steel 1.4404/316L or Alloy C22
PEEK
(FDA agreements)
Electrical connections
Cable glands M20 x 1.5 (for max. 1.5 mm
2
cross-section, shielded)
Complete device data (Fitting S020 + transmitter)
Pipe diameter
DN 06 to 400
Measuring range
0.2 to 10 m/s
Sensor element
Electrodes
Fluid temperature
PVDF sensor version
St.St. sensor version
0 up to 80°C
(32 to 176°F) (depends on fitting)
-15 up to 110°C (5 to 230°F) (depends on fitting)
Fluid pressure max.
PVDF sensor version
St.St. sensor version
see pressure/temperature diagram
PN10
(145.1 PSI)
PN10 (145.1 PSI) (with plastic fitting) - PN16 (232.16 PSI) (with metal fitting)
Conductivity
min. 20 μS/cm
Accuracy
Teach-In
Standard K-factor
(for measured value from 1 to 10 m/s)
≤ ±2% of Reading
1)
≤ ±4% of Reading
1)
Linearity
≤ ±( 1% of Reading + 0.1% of F.S.*)
1)
Repeatability
≤ 0.25% of Reading
1)
Electromagnetic Flow Transmitter
The electromagnetic flow meter Type 8045
has been designed for pipes with diameters
ranging from DN 06 to DN 400 and liquids
having a conductivity > 20 µS/cm.
The transmitter has a display, a keyboard and
provides 4-20 mA, relay and pulse outputs;
The version with a stainless steel sensor has
been designed for applications with high
pressures (PN16) and high temperatures (up to
110°C).
The version with Alloy C22 electrodes has
been designed for applications with aggressive
fluids (chemicals) and especially sea water ap-
plications.
Type S020
INSERTION
T-fitting
Type S020
Spigot
Type 2030
Diaphragm valve
• Sensor in solid state technology
• Shows both flow rate and volume
• Simulation: all output signals provided without the
need for real flow
• Clean in place (CIP), FDA approved
• Version with Alloy C22 electrodes
PLC
Type 8045 can be combined with...
Type 2712
Globe control valve
with TopControl
Type 8644
Valve islands with
electronic I/O
1)
Under reference conditions i.e. measuring fluid=water,
ambient and water temperature=20°C (68°F), applying
the minimum inlet and outlet pipe straights, matched in-
side pipe dimensions.
* F.S.= of Full scale (10 m/s)

Burkert 8045 Specifications

General

Model	8045
Device Type	Transmitter
Measurement Principle	Electromagnetic
Output Signal	4-20 mA
Material	Stainless steel
Lining Material Options	PTFE
Electrode Material Options	Stainless Steel, Hastelloy
Accuracy	±0.5%
Ambient Temperature Range	-20 to 60 °C
Protection Rating	IP65
Certifications	ATEX